Nistune Forums

How can I use the the dlp converter and my LM1 at the same time if i connect the lm1 with the serial cabel?

set the DLP to WB02LH and the LM1 to WB02RH

or chop the serial plug off the LM1 lead and wire it into the DLP

wiring diagram of plug on page 20 http://www.innovatemotorsports.com/supp ... Manual.pdf

andygts wrote:set the DLP to WB02LH and the LM1 to WB02RH

or chop the serial plug off the LM1 lead and wire it into the DLP

wiring diagram of plug on page 20 http://www.innovatemotorsports.com/supp ... Manual.pdf

if i use dlp on wb02lh nistune dont give me the possibilty to use the lm1 on wbo2rh.

so i would like to use the lm1 by an serial connection, so what can I do?

Next release it will let you use the LM-1 and DLP same time. I've made changes to allow this since we were trying to do boost logging and AFR logging (RHS)

Matt wrote:Next release it will let you use the LM-1 and DLP same time. I've made changes to allow this since we were trying to do boost logging and AFR logging (RHS)

when is the next release, matt?

When I get some free time.... I'm in the middle of packing everything up and moving into storage. Should be finished moving by the weekend and some time then to put a beta version together

Matt wrote:When I get some free time.... I'm in the middle of packing everything up and moving into storage. Should be finished moving by the weekend and some time then to put a beta version together

is there anything new matt?

Still packing things up this week. I'm looking at early next week for a beta release

I tried this feature the other day. I can select Innovate MTS to second wideband. I have connected two wideband sensor in series and it works fine when I connect only the Innovate sensors. But when DLP is connected to the first selection and Innovate in second the AFR display shows one figure which is not updated at all. Is there some way I can make this setup work?

have to look at that one...

Any manual to how to integrate and monitor LM1 with nistune ? got the DLP and got the LM one but couldnot mix them up

As of current you cannot do this. Innovate is only available as the primary device. I will have to update to make it available as secondary device and DLP as primary device to allow use of the AUX

I will get it working with all the updates I'm doing to the wideband code since I have DLP for my boost and want to get it running with my Innovate LC-1 in my R34 this long weekend

Once these updates are finished and tested will upload in the next few weeks

Matt wrote:As of current you cannot do this. Innovate is only available as the primary device. I will have to update to make it available as secondary device and DLP as primary device to allow use of the AUX

I will get it working with all the updates I'm doing to the wideband code since I have DLP for my boost and want to get it running with my Innovate LC-1 in my R34 this long weekend

Once these updates are finished and tested will upload in the next few weeks

Thanks Matt we will wait for your updates

Matt, any news fore close future ?

Been working on coding updates all week (even when away). Finished debugging AFR tracer etc updates last night and doing testing tonight

Wideband, consult and auxillary inputs classes are finished. These pipe data into combined sensor class (used for logging recording/playback) and then fed out the gauges, AFR tracing etc

All logging and gauges, tracing work again as expected. Still to retest the following
- Physical wideband units (Innovate, DLP and SLC available to me currently)
- Consult (USB Type 1 and Extended Type 2-4)
- Map highlighting

Then retest Auxillary inputs
- Duty cycle
- Knock counter (testing on VLT, CA18 and HCR32)
- AOI (area of interest in log player)

After this will update code to allow Innovate on WB RHS input (disable on LHS input when selected)