Nistune is a real-time tuning suite designed especially for Nissan vehicles
https://forum.nistune.com/
Add VLT batch/sequential temperature switch and enable switch
Add VLT batch/sequential parameters for injection/RPM trigger point adjustment (needs updated board firmware)
Support for Y33 VQ30DET Feature Pack and Stream TP/Adjust TPS tracing
Add pause button and single cylinder simulation to engine sim controller
Version 1.2.58Add disable switch tuner/stream mode in logger
Add fuel pump prime duration support for Z32 8 bit (firmware update required)
HR33 RB20E connection type fixup
For those having problems with a leanout on S14A SR20DET (only on ADM and EDM versions of ECU), zero out the EGR timer table to resolve this problem!Fix Z31/R31 MAF offset when loading files and changing ECU type using VQ map detection
Add EGR parameter check inside test script
Check feature pack used for P11 VE map tracing
Fix copy to partner bug
Add test warning sounds to engine script test routine
Add Z32 flex crank enrich
Fix Z31 VQ map 1987
Add feature pack (TIM only) for Y60 TB42E
Add EGR timer table for resolving S14A 4 second leanout issue
Add U14 SR20DE support
Add 87 Z31 RB20DET support
Version 1.2.62
Auto tick box R32 GTR MAF
Add Cedrick RB25DET NEO R700
Fix issue with ethanol offsets not displaying in consult
Version 1.2.61
Add Y33 5P7xx support
Version 1.2.60
R32 GTR tick MAF half box by default
AEM UEGO fix lean drop comms issue
Version 1.2.59
Fix crash bug: Open ODD/EVEN crash (introduced 1.2.52)
Fix boost range for zeitronix
Reorder VQ maps so 3-4 R35 GTR MAF VQ shows up as 3-4"
Fix Zeitronix boost range (negative values for this wideband) on log playback
Add VE RPM tracing and TPS fixes for SR20DE
Add N15 SR20DE ATPS VE tracing
Remove VE map autotune code and button (not possible)
Add checkbox to hide extra icons (emualtor/wideband)
Add extra flex fuel limits for fuel and timing tables to prevent wraparouid
Add in checks for duplicate address files
Moates hardware tracing offset fix (8 bit)
Check scaling, tracing and names and cleanup tables S13 CA18DET
Fix FP import ROM image when using different 1-5 selection
Updates to adjust graphics when windows DPI changes on high resolution displays
Fix issue with knock register disappearing when logger opened
Workaround for firmware issue when knock counter increases on upload
Add flags tickbox compare feature
Fix fuel map colouring for +128 maps
Run through all address files and remove duplicated memory addresses
Fixes to CA18DET addresses
Update EGR table (index RPM by TP) for disabling 4 second lean in S14A/S15 ADM/EDM ECUs
Add FP2 latency vs volt table
Add FP2 boost address tracing NEO R34
Add FP2/FP1 address file determination
Update engine simulator for check/report wastegate solenoid
Update memory addresses for FP2 updates (ER34/WC34)
Add IDLE_FUEL table
I've now added the following for FP2 updates:Add VE map tracing for K11 32K version (Type 5)
Updated FP 2 ROM pack 2.4 and Feature Pack 2 documentation forUpdate S14/S15 boost table tracing using ECU addressing
Remove knock volt limit table from S14A/S15
FP2 - Add idle fuel table
Engine sim fiexes for addres range and accept hex parameters
Fix import non-FP looping bug
Version 1.2.68
Add dwell charge time gauge back into software
Version 1.2.72
Update G7 IPC. Fix boost reporting
Consult 1 streaming. Fix bugs with not reporting consult digital reg 1 (TPS idle etc) and small number of consult parameters causing freeze up in comms
Version 1.2.71
Update for G7. Update state machine to fix poll rate. Add retry counter and connect on unit reset
Version 1.2.70
Update for G7 IPC 1.0.0.1 firmware (frame length fix)
Add C2 kernel upload and ROM download sequence
Add C2 ECU identfication and address file matching
Add base idle target maps
Version 1.2.69
Increase maximum image load sizes
Add C2 Kline protocol state machine and processing
Add C2 Kline ECU identification, register probe/display, DTC codes
Add extended memory support for hex editor
Add Garage7 IPC support code. Basic testing only
Add 1996 Z32 ECU ID file detection (10 byte offset)
Update C2 verification and flash processing
Fix LOW_AFM_ENRICH_TRIGGER to different scaling for NEO egines
Fix ECU identification detection bug (Type 1). Causes crash
Add C2 retries when running bootloader
Add 2.5" HPX startup VQ map
Currently adding boost control to some 8 bit ECUs.... starting BNR32 GTR. It has a boost table (TPS vs RPM) but no scaled indexes (impossible to maptrace) and only on/off functionality to enable/disable the solenoid. There are some extra tables added which control the duty cycle. These will be removed and replaced by 2 x boost maps (by gear) and adjustable by ethanol content (well that is the plan... its coded but not tested)Version 1.2.74
Additional BNR32 wastegate tables
Removed warning log message for 'adjusted TPS not found'
Fixes for TP gauge (register selections depending on ECU)
Completed BNR32 FP2 boost control firmware (attached)Updated BNR32 FP2 address locations
Fix idle fuel table filtered display issue
Add warning tone and status update when MAF voltage exceeds 5.05 volts
Fix web update issue where patch release updates are not being detected
Fix BNR32 FP boost reporting cursor
Matt wrote:Version 1.2.75Completed BNR32 FP2 boost control firmware (attached)Updated BNR32 FP2 address locations
Fix idle fuel table filtered display issue
Add warning tone and status update when MAF voltage exceeds 5.05 volts
Fix web update issue where patch release updates are not being detected
Fix BNR32 FP boost reporting cursor