RB25DET with R32 ecu VCT Not working

Nistune topics related specifically to the 6303 cpu

Moderator: Matt

Post Reply
stinger
 

Posts: 7
Joined: Mon Jun 28, 2010 12:14 am

RB25DET with R32 ecu VCT Not working

Post by stinger »

Hi,

How to know which ENT file is program on my type2 board?
I used the "Air Conditioning ouput" solution as described on the "Nistune Feature pack hardware Install.pdf", but if I understand, if my board is program with VFCOUNT.ENT, my VCT can work. Should I use the "Fuel pump idle control output" solution?

(Sorry for my english...)
20170518_212335 (1024x576).jpg
(471.85 KiB) Downloaded 1711 times
Last edited by stinger on Fri Sep 08, 2017 6:18 am, edited 1 time in total.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: RB25DET with R32 ecu VCT Not working

Post by Matt »

That is my bad hand writing. I write exactly what is on the board. You do not have VCT support on that board

This is what is on your board:
HCR32_RB20DET_11U0F_MT_MEC-212B_FP.ent

You will need to remove and have it reprogrammed (using base image programmer) to this:
HCR32_FOR_RB25_11U0F_MT_TPS_VCT_ACOUT_v5_FP.ent
stinger
 

Posts: 7
Joined: Mon Jun 28, 2010 12:14 am

Re: RB25DET with R32 ecu VCT Not working

Post by stinger »

Thanks for your answer.
When I received the Base Image Programmer, I could play with!! :)
stinger
 

Posts: 7
Joined: Mon Jun 28, 2010 12:14 am

Re: RB25DET with R32 ecu VCT Not working

Post by stinger »

Hi,

I think get a problem with VTC.
I updated my board with "HCR32_FOR_RB25_11U0F_MT_TPS_VCT_ACOUT_v5_FP.ent " and map with "HCR32_FOR_RB25_11U0F_MT_TPS_VCT_FP_maps.bin",
Using Air Conditioning ouput".
Pin9 from ecu is cut and pin9 to pin113 are solder.
Sans titre (419x481).jpg
(192.2 KiB) Downloaded 1708 times
If i understand pin 113 operate like a ground. When no ground, VTC off.

At start and for few minutes, "VTC sol" lights in red.
I have 12V at VTC Connector. Ground at pin113.
20170907_130150 (2024x1139).jpg
(599.21 KiB) Downloaded 1708 times
After few minutes, "VTC sol" become grey.
I have again 12V at VTC Connector. Ground again at pin113.
20170907_130042 (2024x1139).jpg
(563.42 KiB) Downloaded 1708 times
I have all time 12V circulating to VTC Connector and pin 113 all time at ground, even when I modify VTC parameter for cut it (minimum speed, Temperature cut...).


When VCT is connect, idle is little bad.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: RB25DET with R32 ecu VCT Not working

Post by Matt »

You are measuring VTC incorrectly with your meter. You must measure 12V with red probe on meter and pin 113 (VTC) should be on your black (ground) probe

You may need to adjust VTC TP enable higher so it does not affect
Post Reply