New User - few (tons) of Questions on CA18DET EDM ECU

Nistune topics specific to the 6802 cpu

Moderator: Matt

Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Okay this looks good. We have LTFT and you can see the adjustments (in those cells traced) in the RAM tracer at 1500
Attachments
2020-08-15 09_40_54-Nistune [S13 CA18DET FP1_ LTFT memory map.png
(70.28 KiB) Downloaded 1757 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Yes the knock count works on the version on the website, but I've disabled in the software unless the 'knock sensor' DTC box is ticked CA18DET didn't have the DTC addresses defined, so you can see them in the attached updated address file (put in Documents/Nistune/Address). I will include the updated version in next release
Attachments
BASE_CA_128_E.adr
(1.49 KiB) Downloaded 76 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Attached is the ENT file I used today for 39F0x ECU part number (with LTFT)
Attachments
S13_CA18DET_39F0H_MEC-D007D_EDM_MT_FP.zip
(16.97 KiB) Downloaded 71 times
PL
 

Posts: 957
Joined: Fri Feb 03, 2006 3:29 pm
Location: Adelaide, South Oz
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by PL »

Nice to have some stuff like this for the mighty CA. Shame we don't see more of them around here in SA.

PL
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Awesome Matt,

thanks a lot for putting so much work into this!

When i try to load the adr file you just posted it gives me an error. Let us know when the official re-release of the CA18DET V1.1 is done

8)
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

What is the error message? It should work with the latest 1.3.29 released 4 days ago
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Hi Matt,

it shows:

Errors in Adress File cannot process!
Error: ROM OFFSET is not specified
Error: ROM ORIGIN is not specified
Error: ROM LENGTH is not specified
Error: CPU type is not specified.

All in one Error box.

Also: How can i open the Consult Ram Tracer with a Type1 Board that has no consult? I cant find the option anywhere.
BEst Regards
Felix
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Hi Felix

Are you opening the file directly, or just putting it over the top of the previous one in your Documents/Nistune/Address folder?

You should just replace the previous version

RAM tracer is only available in Expert mode sorry. File > Config > Misc > User level = expert then restart, and you should see RAM tracer in Display > consult RAM tracer
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Hi Matt,
thanks for the reply.
Matt wrote: Mon Aug 24, 2020 9:58 pm Hi Felix

Are you opening the file directly, or just putting it over the top of the previous one in your Documents/Nistune/Address folder?

You should just replace the previous version
Tried both, if i replace it and go to Select Vehicle -> S13/RS13U12 Silvia/180SX CA19DET it seems to select another adr file.
Nistune asks me if i want to load the Feature Pack adr since it recognizes a feature pack 1 ECU but i tried both loading the adr file for FP1 and leave the File loaded that has been chosen automatically. Both without success so far.

I'll check with RAM Tracer.

Matt wrote: Mon Aug 24, 2020 9:58 pm
RAM tracer is only available in Expert mode sorry. File > Config > Misc > User level = expert then restart, and you should see RAM tracer in Display > consult RAM tracer
Thanks, found it now.

Best Regards
Felix
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Okay just wait for the next 1.3.30 release. I'll try and get that up Friday since I should have some time then
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Hi Matt,

i'll wait, your Friday is my Thursday anyway :lol:
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

Ran out of time Friday. Been crazy busy as usual. Anyway I've put the LTFT into 1.3.30 for S13 CA18DET (standard) + FP1 versions. Release going up now
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Hi Matt,

no worries i was super busy as well and didnt even had the time to check until now.
Works perfectly fine.

Thanks
Felix
Run_Stop_Restore
 

Posts: 22
Joined: Sat Jul 18, 2020 8:05 am

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Run_Stop_Restore »

Matt wrote: Wed Aug 12, 2020 8:16 am Yeah just hold off for that then. I don't have an ETA unfortunately as I'm finishing up FP1.1/FP2.1 for SR20DET currently (half way updating my patching scripts), and then will go back to the knock count work after that
Hi Matt,

any update on FP1.1 re-release with cylinder selective knock count for Type 1 CA18?

Best Regards
Felix
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: New User - few (tons) of Questions on CA18DET EDM ECU

Post by Matt »

No update yet on this one. I'm part time with Nistune, so adding extra features on top of normal support is only when I have free time
Post Reply