rb30 starting issues

Nistune topics specific to the 6802 cpu

Moderator: Matt

Post Reply
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

rb30 starting issues

Post by Ronesh Nand »

Hi guys,

I've got a starting issue with my rb30et powered r31.unable to connect consult with following warning note.i have checked Maf signal to ecm and all is fine (0.45v) just wondered if any one has come across this fault.

when consult does connect it does start and runs fine.but won't connect or start when restarting.
Attachments
IMG_3938.jpeg
(110.23 KiB) Downloaded 1203 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: rb30 https://forum.nistune.com/posting.php?mode=post&f=7starting issues

Post by Matt »

What is the part number (ECU ID) displayed when you do connect?

When does it connect (only when engine not running?)

Does it disconnect when you start cranking, and then not connect again?

Does the engine run okay?

Who installed the board?

What is the MAF voltage shown in the Nistune software?

What MAF are you using (RB30? or Z32 etc)?

Have you done the OPAMP modification (See Type 1 manual, towards end) if using anything but an RB30 MAF?
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

Re: rb30 starting issues

Post by Ronesh Nand »

Hey Matt,

So I’ve managed to find a std Vl rb30 na ecm and she has started. So what I need to do is transfer the mistime rom to the working ecm, unless you can work your magic please? I would also like flex fuel and what ever other feature I can throw on this working ecm .. I’m happy to send the ecms down and cross to you .
bsdkllr
 

Posts: 56
Joined: Wed Mar 09, 2016 5:32 am
Location: Boston, MA

Re: rb30 starting issues

Post by bsdkllr »

I have gotten that same error. And we believe it to be a corrupt flash of the base image of nistune. Matt would be best to give a solid answer if this is your issue.
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

Re: rb30 starting issues

Post by Ronesh Nand »

Iv sort of narrowed it down to ecm not giving a ignition signal to the coil ...
bsdkllr
 

Posts: 56
Joined: Wed Mar 09, 2016 5:32 am
Location: Boston, MA

Re: rb30 starting issues

Post by bsdkllr »

And this is with the nistuned ecu? If so does the fuel pump prime when the key is on or does it stay running?
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

Re: rb30 starting issues

Post by Ronesh Nand »

Yep it sure does .. but I’ve also chucked a relay I. The boot for the fuel pump
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

Re: rb30 starting issues

Post by Ronesh Nand »

And yes it’s with the nistune
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: rb30 starting issues

Post by Matt »

Can you answer the questions I posted above, and then I can help further. I need an answer to each one, to narrow down the issue. For example if it only connects engine off, then doesn't engine on, then I need to know the MAF voltage @ engine off to check that. If it disconnects engine on and doesn't run then there might be an installation issue
Ronesh Nand
 

Posts: 6
Joined: Fri Jan 10, 2020 9:23 am

Re: rb30 https://forum.nistune.com/posting.php?mode=post&f=7starting issues

Post by Ronesh Nand »

What is the part number (ECU ID) displayed when you do connect?
Sorry cant connect ecu at all.

When does it connect (only when engine not running?)
doesn't connect at all

Does it disconnect when you start cranking, and then not connect again?
doesn't connect at all

Does the engine run okay?
yep it was ,but now wont start or run cant connect to consult at all

Who installed the board?
i believe your workshop

What is the MAF voltage shown in the Nistune software?
was showing 0.4 volts when i could connect to it

What MAF are you using (RB30? or Z32 etc)?
genuine z32 with tomei z32 plug

Have you done the OPAMP modification (See Type 1 manual, towards end) if using anything but an RB30 MAF?
yes i have
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: rb30 starting issues

Post by Matt »

Okay you might need to post the ECU here. It sounds like it was working but no longer connecting (corrupted image or damaged board?)

Please post to the PO Box address on our website?

I don't have record of fitting a board for you in our invoice system (only a licence in January). When was the board supplied and fitted? You can shoot me an email info@nistune.com with more info
Post Reply