Consult cant connect

Discuss hardware problems here.

Moderator: Matt

Post Reply
WannaBREz
 

Posts: 22
Joined: Wed Aug 06, 2008 4:25 am

Consult cant connect

Post by WannaBREz »

Searched and searched, I cant find someone with the same problem.

Image

Just got NIStune. I have installed the software and the type 1 xp drivers. I seem to have a unique problem. The computer finds the NIStune fine, and installs the drivers fine. But then, after the NIStune drivers are installed, the computer says there is a USB serial port to install?? I cant find the drivers for that at all.

Image

Does the Romulator have to plugged in as well?? the computer I am using doesnt have a serial port.

I used the USBview and everything there looks fine.
Image

Help!
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt »

Looks like its trying to install the Nistune device as a serial port for some strange reason

If you right click on the Nistune Communications Device and then look through the tabs for 'Create a virtual com port' or something like that. It is a tickbox. Untick this box and then unplug-replug

Hopefully this time that extra device should not show up.
WannaBREz
 

Posts: 22
Joined: Wed Aug 06, 2008 4:25 am

Post by WannaBREz »

Thanks Matt, that took care of the unknown USB serial port. I still cant connect. I logged a debug file. Here it is,

NISTUNE LOG Jul 28 2008 00:26 0.9.2.64
21:22:29.093 CNistuneDoc - usb disconnected
21:22:29.125 CImageSelPanelView
21:22:29.156 ConsultMain()
21:22:29.156 CConsultSM::CConsultSM
21:22:29.156 SetConsultMode(): From 14 to 0
21:22:29.156 CImageSelPanelView
21:22:29.156 CRomulatorSM::CRomulatorSM()
21:22:29.156 RomulatorMain()
21:22:29.156 ProcessRomualtorQueue(0) - Entering thread
21:22:29.156 CImageSelPanelView
21:22:29.156 CRomulatorSM::CRomulatorSM()
21:22:29.156 RomulatorMain()
21:22:29.156 TriggerRomulatorEventTask(1) - Entering thread
21:22:29.156 ProcessRomualtorQueue(0) - Entering thread
21:22:29.156 CImageSelPanelView
21:22:29.156 USBMain
21:22:29.156 TriggerRomulatorEventTask(2) - Entering thread
21:22:29.187 InitialiseRegisters
21:22:29.187 CNIStuneDoc(): Zeroising target AFR table
21:22:29.187 CNIStuneDoc(): Initilising sensor record table
21:22:29.203 CNIStuneDoc(): Initilising RPM AFR trace table
21:22:29.203 CNIStuneDoc(): Initilising consult
21:22:29.203 ConsultGetActiveSelections()
21:22:29.203 Unable to load afr1.csv lookup table - empty file
21:22:29.203 Unable to load afr2.csv lookup table - empty file
21:22:29.203 Unable to load aux1.csv lookup table - empty file
21:22:29.203 Unable to load aux2.csv lookup table - empty file
21:22:29.203 Unable to load aux3.csv lookup table - empty file
21:22:29.203 Unable to load aux4.csv lookup table - empty file
21:22:29.203 Unable to load aux5.csv lookup table - empty file
21:22:29.203 Unable to load aux6.csv lookup table - empty file
21:22:29.203 CImageSelPanelView
21:22:29.218 CImageSelPanelView::OnInitialUpdate
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt »

Sorry but need the another log after you attempt the connection. This one doesnt show the Z31 address file being loaded or the consult button being pressed
WannaBREz
 

Posts: 22
Joined: Wed Aug 06, 2008 4:25 am

Post by WannaBREz »

ok i have the connection log. I will paste it tonight. but it errors out on the driver saying it loads 0 of 10 bytes.
Post Reply