what is it? how to fight it?

Questions that get asked a lot.

Moderator: Matt

tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

what is it? how to fight it?

Post by tr0jan »

:?: :?: :?:

Image
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

Either (a) Nistune board is not installed or (b) the jumper for using Nistune board has not been moved

If the ECU shows ECU ID: 23710-xxxxx and then FACTORY it is not using Nistune board
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

Matt wrote:Either (a) Nistune board is not installed or (b) the jumper for using Nistune board has not been moved

If the ECU shows ECU ID: 23710-xxxxx and then FACTORY it is not using Nistune board
the fact is that this message does not always appear. Work in the program, after a while there is this inscription, it is necessary to restart the engine, and a program to ensure that all functioning again
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

Check the two jumpers on rear of ECU are soldered properly. If the ECU shows 'factory' at any time next to ECU part number then it is not picking up the Nistune board probably because of one of these jumpers not connected properly
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

Matt wrote:Check the two jumpers on rear of ECU are soldered properly. If the ECU shows 'factory' at any time next to ECU part number then it is not picking up the Nistune board probably because of one of these jumpers not connected properly

Image
Image
Image
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

Jumpers on the ECU.... not jumpers on the Nistune board
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

Matt wrote:Jumpers on the ECU.... not jumpers on the Nistune board
what affect a jumper on the ECU? in what place they are, you can specify?
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

See Type 4 hardware installation manual - Photo for Y33 model ECU jumpers in there
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

Matt wrote:See Type 4 hardware installation manual - Photo for Y33 model ECU jumpers in there
oh my god! how to check the work or not?
when I open the throttle, ignition -7. where the fault is?
Image
Last edited by tr0jan on Sat Sep 27, 2014 5:16 am, edited 1 time in total.
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

I restored, checked conductivity. all ok

Image
what do I do with the ignition -7? Who is to blame?
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

not sure. Post the BIN file and log of issue here
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

Matt wrote:not sure. Post the BIN file and log of issue here
I sent you a bin file and log in an email. info[@]nistune.com
tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

tr0jan
 

Posts: 58
Joined: Tue Sep 09, 2014 3:30 am
Contact:

Re: what is it? how to fight it?

Post by tr0jan »

I just need to do? I have no additional power
Image
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: what is it? how to fight it?

Post by Matt »

you emailed me about this also. I've replied back and said that this is only for the Type 4 - dual ROM boards
Post Reply