Search found 233 matches
- Tue May 29, 2012 3:12 am
- Forum: Type 3/4/5
- Topic: made 632 whp but leaning out
- Replies: 14
- Views: 7270
Re: made 632 whp but leaning out
Your max tp appears to 41 during that pull while your map is setup for over double that. The pw commanded is fairly close to the actual pw so that's good but you're only using over half of the available duty cycle. Lots of room to richen up the mixture. You also have the timing map set with feedback...
- Thu Apr 26, 2012 12:27 am
- Forum: General Nistune Discussion
- Topic: VE table and open / closed loop threshold on 70F05 95 S14
- Replies: 14
- Views: 10020
Re: VE table and open / closed loop threshold on 70F05 95 S14
Are you guys unplugging the o2 from the harness as well or just removing it via nistune?
- Tue Apr 24, 2012 11:50 pm
- Forum: General Nistune Discussion
- Topic: who has the highest horsepower nissan on nistune?
- Replies: 15
- Views: 9880
Re: who has the highest horsepower nissan on nistune?
I'm at 425whp with my L28ET. I've also tuned L28's into the 500's with nistune. I think 6 cylinders can count if they only have two valves per cylinder.
- Sun Apr 22, 2012 8:40 am
- Forum: General Nistune Discussion
- Topic: Is it possible to read g/s on a Z32 MAF?
- Replies: 1
- Views: 1514
Re: Is it possible to read g/s on a Z32 MAF?
Someone made a table, no idea on how accurate it is.
http://forums.nicoclub.com/z32-maf-tabl ... 38395.html
http://forums.nicoclub.com/z32-maf-tabl ... 38395.html
- Fri Apr 13, 2012 12:11 am
- Forum: B.S.
- Topic: Australian Users
- Replies: 3
- Views: 4403
Re: Australian Users
Yes I did. I made the flat bar on the trans the same lenght as the throw of the shifter. I went back to a stock shifter. The ratchet shifter sits too high on the console and since the trans was already installed, I'd have to cut the console or remove the trans again to make it fit the way I wanted i...
- Sat Oct 22, 2011 3:32 pm
- Forum: Type 2
- Topic: RB25: converting from high impedence to low....Do I.....
- Replies: 11
- Views: 3451
Re: RB25: converting from high impedence to low....Do I.....
Pardon?skyline_stu wrote:Or I'll go past you both with my old school L28, non crossflow 713hp monsters..
Using a VL ECU of course....
- Mon Sep 26, 2011 3:50 am
- Forum: B.S.
- Topic: Australian Users
- Replies: 3
- Views: 4403
Australian Users
Anyone know someone with a jatco and pro ratchet installed? I've picked one up for my 3n71b and need the length of the lever used at the transmission. Or a good way of calculating it based on the stock lever length.
- Mon Sep 05, 2011 11:13 am
- Forum: General Nistune Discussion
- Topic: z32 Running Rb25 (Problem Controlling larger Injectors)
- Replies: 5
- Views: 2669
Re: z32 Running Rb25 (Problem Controlling larger Injectors)
Have you tried again with new spark plugs?
- Wed May 25, 2011 1:13 pm
- Forum: Type 1
- Topic: drag race tune help please!
- Replies: 3
- Views: 1925
Re: drag race tune help please!
It looks like you have the stock vq map with cobra maf.
- Wed Mar 30, 2011 12:31 pm
- Forum: General Nistune Discussion
- Topic: not sure if its a ecu problem but maybe someone can help
- Replies: 11
- Views: 4195
Re: not sure if its a ecu problem but maybe someone can help
adjust first time injection by the same amount you adjusted the k value for the new injectors. that should give you stock like starting.
- Tue Mar 22, 2011 2:35 am
- Forum: General Nistune Discussion
- Topic: Interesting question
- Replies: 4
- Views: 2630
Re: Interesting question
If you have the 12 feed figured out the rest is easy. Connect the positive of the volt meter to one of the cas outputs in question and the other end of the meter to ground. With the 12vdc connected slowly rotate the cas, you'll see the voltage go up to 5vdc everytime a window or slit in the cas open...
- Sun Mar 20, 2011 10:08 am
- Forum: Test Results
- Topic: L28et bin
- Replies: 12
- Views: 9373
Re: L28et bin
At this point is there any way you can help me create a bin based with the info i have provided that I may be able to correct the current issues and just have to fine tune ? I will be more than happy to compensate for your time and such. thanks . Start with the jwt binfile, go to the operations dro...
- Sun Mar 20, 2011 2:38 am
- Forum: Test Results
- Topic: L28et bin
- Replies: 12
- Views: 9373
Re: L28et bin
Can you explain why the maf table change? What drove you to make those changes? Does jwt delete the tps? It looks like you might want to restart with the jwt binfile and rescale for your new injectors. You raised your k value but lowered your scales, this is the reverse of what you should do. The ma...
- Fri Mar 18, 2011 10:36 am
- Forum: Type 2
- Topic: After start timing Advance BDTC?
- Replies: 10
- Views: 3273
Re: After start timing Advance BDTC?
The idle/decel table is the main idle timing map.
- Thu Mar 17, 2011 11:43 pm
- Forum: Type 2
- Topic: After start timing Advance BDTC?
- Replies: 10
- Views: 3273
Re: After start timing Advance BDTC?
I was talking about the advance table. I have the subtract table zero'd out.