Search found 39 matches

by iyarovoy
Wed Jul 18, 2018 10:40 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

If you could play around with this table on the bench and characterize its effects, that would be very big help! It might be throttle based or RPM based, or the delta-RPM(derivative aka change in RPM) based or deltaTPS (rate of TPS change) or both. Any updates on this? Just curious if you had time ...
by iyarovoy
Wed Jul 04, 2018 11:22 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Those logs look a lot better than before, but still leaning to 16:1 Okay, does that sync table take away that lean spot we are seeing? It happens significantly less, and typically now at throttle tip-in it goes pretty rich, to ~15.3 then back to 14.7 like its supposed to. At very light throttle, it...
by iyarovoy
Wed Jul 04, 2018 3:49 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

I may have narrowed down the map that changes this behavior.

"Sync RPM Factor" in expert view seems to change characteristics.
by iyarovoy
Fri Jun 22, 2018 3:03 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Issue is still there.
Lean_Partial_Throttle.JPG
(210.63 KiB) Downloaded 2422 times
by iyarovoy
Fri Jun 22, 2018 3:01 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Try some stuff here: Keep your fuel values the same for the last two columns, because it is fluctuating between them. Is this a turbo or non turbo setup? Appears you are using around 740CC injectors? This is a Non-Turbo KA24DE with a SR20DET T28 Turbo fitted to it (Basically NA ECU being tuned for ...
by iyarovoy
Sun Jun 03, 2018 8:02 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Looking more through the logs I was surprised to find that the "Injection Time" and "Injector Duty Cycle" are not a derivative of each other (aka Injection Time and Duty Cycle slopes/graphs are often a bit different than each other). It seems like the AFR follows more closely to ...
by iyarovoy
Wed May 30, 2018 5:23 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Log for partial throttle run:
by iyarovoy
Wed May 30, 2018 5:22 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Mr Matt, Thank you for working with me on this. I really appreciate it. Full throttle run: 53F1F_WOT_Run_1to4_Gear.JPG log: 53F1F_Fix_First_Tune_ClosedLoop_1-4th_Gear_Pull.csv Notes: -At WOT, the issue is not present as in the past however, some strange oscillations can be felt as highlighted in the...
by iyarovoy
Sat May 26, 2018 1:36 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

How do you simulate all the inputs into the ECU on the bench? Signal gen for RPM and speed, and variable 12v voltage sources for TPS MAFS and temp? The EGR map you added does make a difference as leanness is not so severe when the map is set to all 0s, however the injection time still does the step ...
by iyarovoy
Fri May 25, 2018 3:29 am
Forum: Type 2
Topic: Rough Cold/ Intial Start Rb25det Neo
Replies: 6
Views: 1462

Re: Rough Cold/ Intial Start Rb25det Neo

.bin file of your tune would be a nice to have.
by iyarovoy
Thu May 24, 2018 4:06 am
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Turns out both MT and AT Feature Pack base bins exhibit this lean behavior, so at this point I dont have a BIN that DOES NOT do this, there fore I cannot narrow down the parameter. Im not sure if I can use non FP bins in Hardware that has a FP Firmware loaded, nor do I want to try this since the iss...
by iyarovoy
Sun May 20, 2018 7:55 am
Forum: General Nistune Discussion
Topic: Nistune Release 1.2.99
Replies: 103
Views: 50454

Re: Nistune Release 1.2.84

NIstune Version 1.2.84 Problem #1 Map Editing feature has a bug. Using +, -, =, %, does not work until you: Does Not Work: nistuneBug_2_1.JPG 1. Type " *1 ", or any multiplication nistuneBug_2_2.JPG 2. Delete the " *1" entry from the field, 3. Now all operations work. nistuneBug_...
by iyarovoy
Wed May 16, 2018 6:12 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Another log to go along with MT_Image_Kvalue.bin attachment that still the lean out clearly visible:
MT_Image_Kvalue_log2.csv
(40.45 KiB) Downloaded 128 times
by iyarovoy
Wed May 16, 2018 3:46 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

Mr Matt, No joy with your updated bin, still lean for the first second on the throttle then injection time spikes (See log + bin). fan_fix_matts_map_2018-05-15_0916_06.csv I was trying to see what you modified in the "Fan Control Flags" and both the old map and your new map look identical,...
by iyarovoy
Fri May 11, 2018 4:23 pm
Forum: Type 3/4/5
Topic: KA24DE-T Injector Resize TP Question
Replies: 51
Views: 16441

Re: KA24DE-T Injector Resize TP Question

I came into possession of a manual s13 KA24DE ECU. do you think if I installed the nistune board with the auto base image into the manual ECU, the lean out would go away?