Search found 31 matches

by omnigear
Thu Jan 25, 2018 11:09 am
Forum: General Nistune Discussion
Topic: Feature Pack updates + Information thread
Replies: 149
Views: 51039

Re: Feature Pack updates + Information thread

Is it possible to use an adruino and its shields to modernized the ecu?
by omnigear
Wed Nov 01, 2017 10:43 am
Forum: General Nistune Discussion
Topic: Feature Pack updates + Information thread
Replies: 149
Views: 51039

Re: Feature Pack updates + Information thread

is the bnr32 feature pack 2 out of beta ? Update: BNR32 Feature Pack 2 available. Same updates as I've done for R34 etc - Boost control - Boost by gear (2 x maps) - Idle fuel table (tickbox) - Latency vs voltage table (replacing latency parameter and voltage adjustment) Looking at Z32 ECU next depen...
by omnigear
Fri Oct 27, 2017 12:29 pm
Forum: General Nistune Discussion
Topic: Nistune Release 1.2.99
Replies: 103
Views: 28477

Re: Nistune Release 1.2.77

Matt can we get a pinned thread that only you can post and edit on what changes have been done to nistune, like a Patch notes thread. It is cumbersome looking for what has changed for X board or if X feature is in beta/added/in-progress. So it would be every post is every major patch or revision.
by omnigear
Wed Nov 23, 2016 4:29 pm
Forum: General Nistune Discussion
Topic: Feature Pack updates + Information thread
Replies: 149
Views: 51039

Re: Feature Pack updates + Information thread

Matt wrote:Added Feature Pack V2 release (beta) for limited range of vehicles
Do feature v1 boards need another reflash or just download the new nistune software?
by omnigear
Tue Jun 28, 2016 4:43 am
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

Re: R35 Maf problems

i have done that, i ticked the halve box and the double box, choose r35 maf 3" > commit change > OK , then i start up the vehicle. Curve is not correct in file. when doing the resize tick the 'halve' button edit: it seems i fail to read and comprehend >_< it says tick double if using the stock rb26 ...
by omnigear
Tue Jun 21, 2016 2:55 am
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

Re: R35 Maf problems

this time around i just adjusted the TIM and left the k constant alone, but the result was the same. after i drive it and park it would loose it shit and go pig rich
by omnigear
Sun Jun 19, 2016 1:01 pm
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

Re: R35 Maf problems

clean maf, checked the wiring for connectivity issue, check for vac leak and in the log the car started driving fine then i pulled over at the house and it went rich as a pig. i would appreciate any insight to my hindsight to solve this problem. also in the change maf option it still says none detec...
by omnigear
Sun Jun 19, 2016 6:54 am
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

Re: R35 Maf problems

Changed pipes to the greddy , changed the maf but it does not say that i am using the r35 after the changes. Am i missing something , because the car was acting up later on the day.
by omnigear
Mon May 09, 2016 11:18 pm
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

Re: R35 Maf voltage difference

the afr is not really consistent, it would swing about 1.2-2.3 . I will try to do what you recommend and see about the pipes. I did not check or logged the stock setup >_< The ECU will work with an average of both sensors. Was is doing that with the factory setup? What if you swap the sensors, does ...
by omnigear
Mon May 02, 2016 9:18 am
Forum: Type 2
Topic: R35 Maf problems
Replies: 8
Views: 2539

R35 Maf problems

i am not sure if this is a problem or not, but i wired in some hitachi r35 mafs on my bnr32 with 3" x2 pipe . It seems on is reading higher than the other on the voltage and is this normal?
by omnigear
Wed Apr 27, 2016 12:39 pm
Forum: General Nistune Discussion
Topic: LS2/LS7 coils and DWELL Time
Replies: 87
Views: 32355

Re: LS2/LS7 coils and DWELL Time

got it sorted out, had vacuum problems .
Matt wrote:DTC21 is a feedback issue from the coils (since they differ to factory). You will not be able to remove the fault code itself due to the electrical characteristic differences. However the raised fault code should not affect the operation of the ECU otherwise
by omnigear
Sun Dec 20, 2015 10:16 pm
Forum: General Nistune Discussion
Topic: LS2/LS7 coils and DWELL Time
Replies: 87
Views: 32355

Re: LS2/LS7 coils and DWELL Time

idk , i cannot even commad the idle above 1.2k or lower on nistune even if I change it.
i have the dwell back to stock and it still the same symptoms.
bachig24u wrote:omnigear, I will be checking an RB25 that had a LS1 coil swap this week. also has DTC 21.
I'll check if the idle issue is related to DTC 21.
by omnigear
Mon Dec 14, 2015 10:52 pm
Forum: Type 2
Topic: RB26 Intake Temp Sensor Upgrade
Replies: 3
Views: 1243

Re: RB26 Intake Temp Sensor Upgrade

this table?
by omnigear
Sun Dec 13, 2015 3:17 pm
Forum: General Nistune Discussion
Topic: LS2/LS7 coils and DWELL Time
Replies: 87
Views: 32355

Re: LS2/LS7 coils and DWELL Time

I am getting a DTC 21 and I cannot command idle , it sticks at 1.2k instead of 950. I have checked vac leaks and nothing comes up.
by omnigear
Wed Dec 09, 2015 10:17 pm
Forum: General Nistune Discussion
Topic: raspberrypi 2 + win10 = Nistune
Replies: 7
Views: 1544

Re: raspberrypi 2 + win10 = Nistune

would something like a wrapper be possible like http://izpack.org/