Search found 232 matches

by BlueRB240
Tue Jan 22, 2019 6:46 pm
Forum: Type 3/4/5
Topic: S14 KA24DE
Replies: 2
Views: 187

Re: S14 KA24DE

ahhh ok. I figured out the check engine light. The wording was confusing me. I had the flag checked because it said egr temp sensor off.
by BlueRB240
Sun Jan 20, 2019 10:04 pm
Forum: Type 3/4/5
Topic: S14 KA24DE
Replies: 2
Views: 187

S14 KA24DE

I'm getting an over temp red light shows up in the bottom right corner in the nistune software? Also my car doesn't have the EGR system anymore but when I uncheck EGR system and leave egr temp sensor off checked I still get a check engine light for EGR related items.
by BlueRB240
Mon Jan 14, 2019 6:53 am
Forum: FAQs
Topic: Loading Old Bin into New version of Nistune
Replies: 7
Views: 2656

Re: Loading Old Bin into New version of Nistune

Sorry been at work all week. I did resize but it was just once which is weird. I will try the changes later today and thanks.
by BlueRB240
Tue Jan 08, 2019 4:24 pm
Forum: FAQs
Topic: Loading Old Bin into New version of Nistune
Replies: 7
Views: 2656

Re: Loading Old Bin into New version of Nistune

This is the file I had loaded on the ecu. It would start for 10 seconds then shut off.
by BlueRB240
Mon Jan 07, 2019 2:53 pm
Forum: FAQs
Topic: Loading Old Bin into New version of Nistune
Replies: 7
Views: 2656

Re: Loading Old Bin into New version of Nistune

I also have a question about this. my bin file was used in march of last year and since then I didn't touch it because the car ran fine. Blew my head gasket it November and the car sat till I got around to fixing it 3 weeks ago. I installed nistune onto a new laptop downloaded the map and made a few...
by BlueRB240
Sun Aug 05, 2018 10:08 am
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

confirmed it is set to 255 for the TP and speddo works. At idle you can hear it clicking the solenoids on and off. It's not long enough for the VVL to kick in so far just annoying.
by BlueRB240
Thu Jul 26, 2018 3:18 pm
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

Pin 105 is bridged directly to 102. This is since there is no circuit on pin 105 in the B13 ECU. So just run a wire between them The output should switch to ground (and activate the solenoid) when you see the VCT indicator in the 'consult view' panel active Also set the TP enable parameter to 255 T...
by BlueRB240
Fri Dec 29, 2017 9:03 am
Forum: General Nistune Discussion
Topic: Y34 M45
Replies: 2
Views: 899

Re: Y34 M45

Damn I hope a AFC will works then. The price on them has been going down lately to 1200ish for engine trans harness and ecu. Thanks for the info Matt.
by BlueRB240
Thu Dec 28, 2017 6:04 pm
Forum: General Nistune Discussion
Topic: Y34 M45
Replies: 2
Views: 899

Y34 M45

Anyone know of something that can be used to tune these ecu's? long shot but I'm running out of places to search.
by BlueRB240
Tue Nov 14, 2017 5:09 pm
Forum: Software Bugs
Topic: 1995 S14 KA24DE
Replies: 1
Views: 776

1995 S14 KA24DE

I haven't opened nistune in about a year. updated to the new version and now when I check the volumetric efficiency map the tracer only moves vertical and only on the 1st load cell. The fuel and timing all trace normal still.
by BlueRB240
Sat Nov 11, 2017 7:29 am
Forum: Type 3/4/5
Topic: Rev limiter?
Replies: 37
Views: 11964

Re: Rev limiter?

Anything new with this?
by BlueRB240
Sat Sep 05, 2015 8:15 pm
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

The safety rev limit was set at 8000 too. Will look into the speedo problem tomorrow.
by BlueRB240
Fri Sep 04, 2015 4:34 pm
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

The spedo isn't working but I'm not getting a code for speed sensor. I'm not sure if its a cluster problem been that its a nx1600 digital cluster.
by BlueRB240
Thu Sep 03, 2015 7:31 pm
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

got the errors again, grounds are good. Also noticed that the rev limiter isn't working. I have it set to 8000 and watched the tach race past 8000 rpm.
by BlueRB240
Tue Sep 01, 2015 3:08 pm
Forum: General Nistune Discussion
Topic: Using the VTC to kick VVL on B13 ecu
Replies: 24
Views: 6746

Re: Using the VTC to kick VVL on B13 ecu

I just checked and the debug was off. I forgot I did a fresh install of nistune. I'll get out to the car again in a few days and I'm sure it will crash on me again. Do I email the logs to enquiries@nistune.com ?