Search found 633 matches

by Torque
Thu Mar 28, 2019 5:45 am
Forum: General Nistune Discussion
Topic: Nistune 1.3
Replies: 22
Views: 2452

Re: Nistune 1.3

I just had a look at 1.3 .. looks nice.

Question:
Are the external CSV files for WB still used?
So can I just copy my modified version into the WB directory?
by Torque
Thu Mar 28, 2019 5:42 am
Forum: General Nistune Discussion
Topic: Nistune 1.3
Replies: 22
Views: 2452

Re: Nistune 1.3

On that note I noticed that the installer places a mts.dll in its base directory and as far as I remember I was told that there should be only one instance of that dll in the system (the one installed by LogWorks)

As for connectivity issues I'll test the new version in a bit with my Innovate WB
by Torque
Tue Feb 05, 2019 5:00 am
Forum: Software Enhancements
Topic: Disable 'Setup Window' at startup
Replies: 2
Views: 1001

Re: Disable 'Setup Window' at startup

Thanks ...
by Torque
Mon Jan 28, 2019 2:48 am
Forum: Software Enhancements
Topic: Make 'ESC' not close windows when in input mode!
Replies: 4
Views: 242

Re: Make 'ESC' not close windows when in input mode!

:)

Cheers ... yeah .. you press 'ESC' to get out of the cell edit mode and the whole window closes ... :shock:
by Torque
Sun Jan 27, 2019 8:36 pm
Forum: Software Enhancements
Topic: Disable 'Setup Window' at startup
Replies: 2
Views: 1001

Disable 'Setup Window' at startup

The pop up window at startup is not really something I want to close manually each time I start NT. :(
While it might be helpful to newcomers there should be an option to disable this. :) (please!)
NTNAG.JPG
NTNAG.JPG (130.33 KiB) Viewed 1001 times
by Torque
Sun Jan 27, 2019 8:30 pm
Forum: Software Enhancements
Topic: Make 'ESC' not close windows when in input mode!
Replies: 4
Views: 242

Make 'ESC' not close windows when in input mode!

Maps should not completely close and disappear when you press 'ESC' in input mode (or not at all actually)
NTESC.JPG
NTESC.JPG (164.12 KiB) Viewed 242 times
by Torque
Fri Oct 05, 2018 7:26 pm
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Re: Calculation basis for estimated AFR?

Thank you .. it seems like a lot of moving targets for the calculation. But how (based on what) do you calculate the estimated pule-width in that table view then? I will have a look at the injection times from the .log, these are the real values I hope? No there isn't an estimated calculation. It wo...
by Torque
Thu Oct 04, 2018 9:38 pm
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Re: Calculation basis for estimated AFR?

OK, thanks Matt ..

I think I got all the information then.

Is there a value in NT that shows the actual result of the injector time calculation?
I would think that your estimated pulse-width is based on that?
by Torque
Thu Oct 04, 2018 1:24 am
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Re: Calculation basis for estimated AFR?

So that's from the document ... I think it does not make it clear at all what actually is going on.
:(

If I understand you correctly a 'filtered value' of lets say '30' at TP 50 will not give the same mixture as '30' at TP 100.

NT_FUEL.JPG
NT_FUEL.JPG (93.66 KiB) Viewed 828 times
by Torque
Wed Oct 03, 2018 7:56 pm
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Re: Calculation basis for estimated AFR?

Thank you, that's helpful. I think I know all the PDFs on there but to my knowledge none outlines the problem in bold writing. I just did a log Estimated vs actual AFR values.. My K is spot on, but as you said on higher loads the actual mixture deviates. What would you suggest to do to bring TP > 52...
by Torque
Tue Oct 02, 2018 8:46 pm
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Re: Calculation basis for estimated AFR?

OK, thanks .. I knew it was somewhere on this forum but didn't find it.

So is there still a point in setting the fuel map to a predefined value and adjust K to match these estimated AF ratios?
Also the autotuner must have some merit? (I've not used it yet)
by Torque
Tue Oct 02, 2018 6:22 am
Forum: General Nistune Discussion
Topic: Calculation basis for estimated AFR?
Replies: 11
Views: 851

Calculation basis for estimated AFR?

I was wondering how the estimated AFR values are guestimated? If I understand it correctly you don't have any airmass values from the MAF sensors .. it's % vs voltage you have(?) Also there is no direct value for injector capacity (?) I might be totally wrong with my assumptions, would be interestin...
by Torque
Mon Oct 01, 2018 10:20 pm
Forum: Type 2
Topic: Aux Fan Control on Z32TT ECU on RB25?
Replies: 4
Views: 922

Re: Aux Fan Control on Z32TT ECU on RB25?

Thanks Matt.

I guess (as you say) just use line 19 (half blow)
Or just bridge 19+6 internally ...

Do you recall what value that SMD resistor has which was removed on Z32 ECU?
Is it important? Must be low ohm?
Z32Cooling.JPG
Z32Cooling.JPG (71.81 KiB) Viewed 904 times
by Torque
Mon Oct 01, 2018 2:49 am
Forum: Type 2
Topic: Aux Fan Control on Z32TT ECU on RB25?
Replies: 4
Views: 922

Aux Fan Control on Z32TT ECU on RB25?

I was wondering if I could use Pin 6 of the Z32 ECU to switch a relay based on coolant temperature. Pin 19 is used for half blow fan speed, pin 6 for full blow. However Pin 19 (On Z32) is cut during installation since it collided with the RB25 Power steering signal. What's left is Pin6 as an output....