Page 1 of 1
new to nistune from stock ca18det base map to 400bhp + map
Posted: Fri Aug 01, 2014 1:52 am
by jks1customs
Hi to all i am new to nistune i been running a base ca18det map , but now i got my mates 400bhp plus map ,i have loaded to my ecu but for some reason the car starts and drives and comeson boost all the way when with the base map boost , petrol and speed was limited
was this meant to happen ??
i should have to run it the following parts
720cc injectors
z32 maf
gt2871r
and some other mods for benerfit i got the tomei pon cams spec
260 duration
8.8mm lift
plus my hks gt2835r
what can i do to correct my map ??
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Fri Aug 01, 2014 7:01 pm
by Matt
I don't really understand what is going wrong in the first sentance... after three re-reads
Do you have a tune and log file you can post here? Do you understand what is in your mates tune?
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Sat Aug 02, 2014 12:29 pm
by jks1customs
i have now uploaded the file can please anyone
what would be the injectors K value and latency of the 750cc rc injectors??
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Mon Aug 04, 2014 9:18 am
by Matt
The file appears to be invalid. Perhaps only the maps were synced from the board. Make sure ROM pack is installed when syncing maps
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Mon Aug 04, 2014 10:12 am
by jks1customs
Ok thats good news for me as I was thinking that I had a damaged maf or bad injectors
Also I got the rc 750cc incjectors what would be the latency and k value on those
The map i am getting was meant to work with 720cc injectors and I got 750cc can I run it without any changes or should I manualy adjusts the k and latency then permanently burn it to my board ??
Thanks in advance Matt
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Mon Aug 04, 2014 2:02 pm
by Matt
Get the file again (the full file, not one with just a few maps in it)
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Tue Aug 05, 2014 9:37 am
by jks1customs
I WILL COPY IT AGAIN, DOES IT MATTER WHEN I COPY THE MAP LIVE MY STOCK INJECTORS AND MAF OR DO I HAVE TO PUT THE Z32 AND MY 750CC INJECTORS THEN COPY IT??
WHATS THE BEST WAY TO COPY IT SAFE I HAVE UPDATED MY ROOM PACK SO ALL SHOULD BE GOOD NOW
LET ME KNOW SO I CAN DO THE BEST WAY
THANKS
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Tue Aug 05, 2014 9:46 am
by jks1customs
I GOT NISTUNE BASE MAP ON MY CA18 STOCK INJECTORS AND MAP WOULD THAT DISTURB THE NEW PLUGGED ECU THAT I AM GONNA USE TO COPY THE MAP OR IT HAS TO BE COPIED WITH THE 720CC AND Z32 MAF ??
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Sat Dec 27, 2014 6:38 pm
by jaredperry
What is happening in this thread?
Re: new to nistune from stock ca18det base map to 400bhp + m
Posted: Sat Dec 27, 2014 11:56 pm
by Matt
What appears happened is you yelled in the thread (CAPS) and no one responded
I've got a tune (attached) which is for Z32 MAF/750CC (close enough starting point) for you to upload and try out to see if it starts
After warming up, see if you can get cruise around 14.7:1 and you should be good
Whatever the previous tune from your friends vehicle that was downloaded resulted in a dud file which could not be used to assist you
Re: new to nistune from stock ca18det base map to 400bhp + map
Posted: Wed Jul 12, 2017 9:38 am
by jks1customs
sorry for the confusion , when i wrote this msg my phone was playing up