Page 1 of 1
TP load scale
Posted: Thu Dec 20, 2012 9:27 am
by sky Z
I have done some logs/runs to tune the AFR´s , and i saw that i hit the max TP load in the fuel map and ignition (they are set to 64)
should i rise up my scale to 76/80 like it show in the multiple display?
tks!
Re: TP load scale
Posted: Thu Dec 20, 2012 2:12 pm
by Matt
Yes this is what should be done next. Rescale the TP load scale for fuel and timing upto the maximum load read (see tuning guide for more info)
Re: TP load scale
Posted: Thu Dec 20, 2012 11:46 pm
by sky Z
Matt wrote:Yes this is what should be done next. Rescale the TP load scale for fuel and timing upto the maximum load read (see tuning guide for more info)
Tks matt, i did this changes compared to the "stock" tune
Also i saw that i had some timing adv below 70º , my engine normal temp is around 67º and 70º (nismo termostat)
Re: TP load scale
Posted: Fri Dec 21, 2012 1:33 am
by unex
read old, but good Pete's post about rescaling.
forum.nistune.com/viewtopic.php?f=12&t=763
Re: TP load scale
Posted: Sat Dec 22, 2012 7:13 am
by sky Z
unex wrote:read old, but good Pete's post about rescaling.
forum.nistune.com/viewtopic.php?f=12&t=763
Good info tks
I did this changes in my map in the TP scales, is bit big scale because in my actual tune at only 16psi of boost i hit the 76 TP load... my turbos (GT2860RS) have a lot more to give.
Also adjust my timing for the bigger TP load
And this is a soft rescale of the same map
Good? no?
Re: TP load scale
Posted: Sun Dec 23, 2012 2:42 pm
by Matt
Bit of a jump between 40 and 70 there?
Re: TP load scale
Posted: Sun Dec 23, 2012 8:33 pm
by unex
sky Z wrote:unex wrote:read old, but good Pete's post about rescaling.
forum.nistune.com/viewtopic.php?f=12&t=763
Good info tks
Good? no?
BAD.
you didnt understand that topic which I gave you. Why you should need so much points between 0 and 40? It could be in 4-5 columns because this is no load area. While 50-100 area is where the things happen.
Re: TP load scale
Posted: Mon Dec 24, 2012 1:22 am
by sky Z
unex wrote:sky Z wrote:unex wrote:read old, but good Pete's post about rescaling.
forum.nistune.com/viewtopic.php?f=12&t=763
Good info tks
Good? no?
BAD.
you didnt understand that topic which I gave you. Why you should need so much points between 0 and 40? It could be in 4-5 columns because this is no load area. While 50-100 area is where the things happen.
You r right
Matt wrote:Bit of a jump between 40 and 70 there?
I made this today
Re: TP load scale
Posted: Mon Dec 24, 2012 10:10 am
by Matt
Also look at the graph using the 2D scale also (Fuel scale) when smoothing. You usually want more resolution (closer numbers) at the top end
Re: TP load scale
Posted: Mon Dec 24, 2012 10:38 am
by sky Z
Matt wrote:Also look at the graph using the 2D scale also (Fuel scale) when smoothing. You usually want more resolution (closer numbers) at the top end
Got it! tks matt
