Launch control update

Discuss hardware enhancements, suggestions, and wishes here.

Moderator: Matt

MJD5SS
 

Posts: 45
Joined: Wed Apr 17, 2013 6:24 pm

Launch control update

Post by MJD5SS »

Hey guys, just wondering if you're still working on the launch control update within Nistune, so very keen on this.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

Yes. Type 4 OBD-II board issues resolved last week so finishing up hardware changes for this and then working on firmware updates next
MJD5SS
 

Posts: 45
Joined: Wed Apr 17, 2013 6:24 pm

Re: Launch control update

Post by MJD5SS »

Beautiful!
Trbulnt
 

Posts: 2
Joined: Sun Jul 28, 2013 9:37 pm

Re: Launch control update

Post by Trbulnt »

Any update on this for Type 1 boards?
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

Type 3/4 boards firstly. Lots of work in progress. Having a lot of code to go through
Trbulnt
 

Posts: 2
Joined: Sun Jul 28, 2013 9:37 pm

Re: Launch control update

Post by Trbulnt »

Thanks for the update and all the hard work!
s13_silvia_redtop
 

Posts: 46
Joined: Sat Sep 05, 2009 6:26 am
Location: tulsa, ok

Re: Launch control update

Post by s13_silvia_redtop »

hey matt, just wondering how the coding is going? i know you have been asked a million times but... heres another impatient person haha also once you are done with this and ready to roll out will it just be an update or a mail my ecu to you type thing?

Thanks!
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

Basically I am updating my disassembler so I can decompile and then recompile the factory code. This part is still in progress and is vehicle dependent. It makes changes easier than patching the code and allows for more change. however it will limit the models I can modify since the process is not automatic. That part is still in progress as well as going through each vehicle code disassembly
s13_silvia_redtop
 

Posts: 46
Joined: Sat Sep 05, 2009 6:26 am
Location: tulsa, ok

Re: Launch control update

Post by s13_silvia_redtop »

sounds like you have your work cut out for you lol good luck and i cant wait to see the final result! :P
OptimumSE-R
 

Posts: 5
Joined: Sun Nov 29, 2009 3:44 pm
Location: Los Angeles
Contact:

Re: Launch control update

Post by OptimumSE-R »

Praying to the Nissan gods this gets done within the next 20 days...
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

Wont happen before then. Two words... school holidays. Seriously though I work some days between 8-12 hours, and that sometimes doesnt even include time for coding updates due to tech support (forum, email and phone calls) in addition to orders, general enquiries, application debugging and updates

I'm still going through code today for the S14 KA model working through injection routines at the moment
MJD5SS
 

Posts: 45
Joined: Wed Apr 17, 2013 6:24 pm

Re: Launch control update

Post by MJD5SS »

can't wait!! :mrgreen:
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

An update. I've almost finished rewriting my disassembler now for reassembling code. Over 300 instructions so took a bit of time but its back up and working. More progress next week
jlag
 

Posts: 1
Joined: Thu Mar 20, 2008 11:00 am

Re: Launch control update

Post by jlag »

Any updates on this ?
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Launch control update

Post by Matt »

More school holidays plus other things like the latest software release have delayed things. Working again on it this week
Post Reply