Wideband AEM Failsafe 30-4900 connection

Anything related to the AEM brand of wideband devices.

Moderator: Matt

me1nik
 

Posts: 1
Joined: Fri Jun 27, 2014 12:46 pm
Location: Russia

Wideband AEM Failsafe 30-4900 connection

Post by me1nik »

Hi Guys.
After a few weeks, gone to connect to the AEM Failsafe Nistune get positive results.

Thanks to Matt for the fact that yesterday completed the program in recent changes and I tested it all works well, you now post the instructions on connecting.

1.) Install com0com: http://sourceforge.net/projects/com0com/
2.) As Administrator, run this from the cmd line: "Bcdedit.exe -set TESTSIGNING ON"
3.) Restart your PC and configure com0com with these settings (check the boxes first, then hit apply; you'll see the COM ports and not CNCB ports then):
Image
- Note the two COM port #'s chosen by com0com
4.) Configure Nistune to use AEM UEGO / Boost and one of the COM ports as configured in com0com
nistune.jpg
(191.82 KiB) Downloaded 8763 times
5.) Install and run app
AEM_WBFS-Bridge_v0.6.zip
(124.67 KiB) Downloaded 256 times
and then choose the other COM port # Turn on debug AFR output if you'd like.
WBFSB.jpg
(44.57 KiB) Downloaded 8763 times
6.) Start up logging on Nistune, and it should just work.

Notes: The program can also be run without the need for any keyboard interaction as follows: "WBFS.exe 5" (where "5" is for COM5) or even simply "wbfs 5"

Do NOT run alongside the AEM Wideband Failsafe software as they will fight each other for USB traffic and logging will be completely wrong. This program runs stand-alone.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

Thanks for posting the instructions!
kgriffin
 

Posts: 33
Joined: Fri Jan 31, 2014 2:40 am

Re: Wideband AEM Failsafe 30-4900 connection

Post by kgriffin »

Awesome thanks for posting this!! Quick question, are you able to record your boost in nistune with this? My AFR's are registering but not the boost, any suggestions?
Rob280z
 

Posts: 4
Joined: Sat Jul 08, 2017 6:41 pm
Location: California

Re: Wideband AEM Failsafe 30-4900 connection

Post by Rob280z »

I am having a bit of an issue setting up my AEM 30-4900 Wideband to Nistune. I downloaded com0com and I am able to create a COM port. I also have AEM Wideband Bridge downloaded and I can see real time numbers of AFRs on this program. When I try to connect the wideband to Nistune after I have configured the COM port, the wideband page opens but reads no wideband found (see photo). I have tried using different COM ports and restarting programs but so far I have had no luck connecting the wideband to Nistune. Also I have closed all programs except Nistune and tried to connect but I still was not able to find the wideband.

Any ideas?

Thank you
Attachments
Wideband Connection 2.jpg
(197.16 KiB) Downloaded 7186 times
Wideband Connection.jpg
(260.74 KiB) Downloaded 7186 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

As per email (duplicate of this post) please make a debug log and email through
Rob280z
 

Posts: 4
Joined: Sat Jul 08, 2017 6:41 pm
Location: California

Re: Wideband AEM Failsafe 30-4900 connection

Post by Rob280z »

I found my issue, which was a very simple mistake. I needed to select COM 16 for the AEM Wideband Bridge and COM15 in the configurations tab in Nistune. Once I connected to the correct COM ports Nistune recognized my wideband.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

Okay excellent!
Torque
 

Posts: 639
Joined: Wed Jun 16, 2010 10:08 am

Re: Wideband AEM Failsafe 30-4900 connection

Post by Torque »

I'm just hooking in here, so are you able to log boost and afr in NT?

Thanks
louiswun
 

Posts: 256
Joined: Tue Apr 07, 2009 1:11 am
Location: Hong Kong

Re: Wideband AEM Failsafe 30-4900 connection

Post by louiswun »

Thank you Me1nik, it works excellent.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

Torque - depending on wideband/gauge but yes you are in 1.3.1 can do AFR/boost combinations
Shane001
 

Posts: 10
Joined: Mon Jul 24, 2017 2:32 pm

Re: Wideband AEM Failsafe 30-4900 connection

Post by Shane001 »

Does this use the USB connection from the failsafe gauge or the analog output wires connected via serial port to a FTDI USB/Serial converter?

Editing this post again as the posts that follow are wrong. Yes this does use the USB connection from the failsafe gauge.

The downside is this method will only log AFR/Lambda, it doesn't allow you to log the boost signal.

Matt, maybe you can clean up this thread by deleting the following posts to avoid any confusion for others.
Last edited by Shane001 on Sun Nov 08, 2020 9:07 pm, edited 1 time in total.
Shane001
 

Posts: 10
Joined: Mon Jul 24, 2017 2:32 pm

Re: Wideband AEM Failsafe 30-4900 connection

Post by Shane001 »

So next question, which wires to connect to which pins on the DB9 connector.

White is AFR - should this go to pin 2 same as the UEGO?
Brown is Ground - should this go to pin 5 same as the UEGO?
Yellow is Boost - which pin should this go to?

Thanks.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

I'm not familiar with the wiring on these, but if you have a AFR and boost output, then these are analog 0-5V outputs most likely, and you will need a DLP A/D converter to read those

Serial connections on the UEGO were RX and GND

So you are not seeing a COM port? I'm not sure on that then
Shane001
 

Posts: 10
Joined: Mon Jul 24, 2017 2:32 pm

Re: Wideband AEM Failsafe 30-4900 connection

Post by Shane001 »

Hi Matt,

Yeah I've since realised I need the DLP A/D converter for the failsafe gauge so ordered this from Digikey.

Today I successfully wired up and tested my AEM UEGO gauge via a DB9 serial port and FTDI converter. This gauge is for the right bank (Z32).

Now I just need to understand how to wire up the DLP for the AEM Failsafe gauge to log the left bank AFR's and boost.

The failsafe has 3 wires:
Yellow = Boost 0-5v analog output
White = AFR 0-5v analog output
Brown = ground analog output

So do I wire this as follows on the DLP?
White into port 1.
Yellow into port 2.
Brown into GND.

Regarding grounding the other inputs, do I just connect ports 3 through 8 together and then connect these to GND also?
Or just connect all the unused inputs to a chassis ground?
Does anything need to be connected to the 5V port on the DLP?

Thanks :)
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: Wideband AEM Failsafe 30-4900 connection

Post by Matt »

That wiring is correct what you have written. Then small pieces of wire or a single strand from ground (on the DLP) through to the other pins to stop the inputs flapping
Post Reply