Wiring in consult plug

If you know what B.S. stands for you know what goes here.

Moderator: Matt

Post Reply
aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Wiring in consult plug

Post by aleks » Sat May 02, 2009 1:16 pm

Just a quick question

I have a CA18 180 with a neo engine. I am going to wire in a consult plug and just wanted to check if I will need the CLK to be wired in (I'm assuming thi is the clocking reference?) because I can't find it in the wirring diagram

Image

Image


So will I need to wire in CLK?


Any help is appreciated.



Cheers, Alex.

Matt
Site Admin
Posts: 8191
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt » Sat May 02, 2009 2:12 pm

yes you need to wire in CLK, TX, RX, 12+, GND

details in here
http://www.nistune.com/docs/Installatio ... ostics.pdf

aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Post by aleks » Sat May 02, 2009 2:37 pm

Anyone know what pin number is CLK for a R34 NEO?

aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Post by aleks » Sat May 02, 2009 3:19 pm

I had to solder from the board thanks to some awesome wiring job :?

You wouldn't happen to know what pin number CLK is Matt? Neo connector isn't in the installation guide.


Cheers, Alex.

Matt
Site Admin
Posts: 8191
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt » Sat May 02, 2009 11:41 pm

silly me... ER34/WC34 RB25 doesnt have the clk line... just remembered. sorry about that

aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Post by aleks » Sat May 02, 2009 11:42 pm

Sweet, thanks.

datsunboy
Posts: 106
Joined: Thu Mar 15, 2007 1:51 pm
Location: New Zealand

Post by datsunboy » Sun May 03, 2009 1:19 pm

Is there any point to wiring a consult port into a CA18?
I thought they didnt have consult?
or is this for a Nistune CA ecu?....then whats the benfit of a consult port?

aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Post by aleks » Wed May 06, 2009 3:34 pm

I have a CA model 180... it never had a consult plug.

It now has RB25 neo (type 4 board) so I had to wire in a consult plug for it as only the type 1 boards have the usb consult add on.

Matt
Site Admin
Posts: 8191
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Post by Matt » Thu May 07, 2009 12:52 am

engine conversion :wink:

datsunboy
Posts: 106
Joined: Thu Mar 15, 2007 1:51 pm
Location: New Zealand

Post by datsunboy » Thu May 07, 2009 12:06 pm

so obviously you got rid of the CA18 loom when you changed to an RB25....so if you used the RB25 loom, wouldnt that have a consult plug???

aleks
Posts: 17
Joined: Sat Jan 24, 2009 9:33 pm

Post by aleks » Sat May 09, 2009 5:49 pm

aleks wrote:I had to solder from the board thanks to some awesome wiring job :?
Not my work

Post Reply