how to connect LC1 to nistune?

Anders_r · Post by **Anders_r** » Mon Aug 10, 2009 10:42 am

Hello guys

I have tried the search but did not find, maybe i search bad ^^

anyway: how to connect LC1 to nistune?

maybe someone can link a picture how u did ?

/Anders

Matt · Post by **Matt** » Mon Aug 10, 2009 6:06 pm

connect 3.5mm connector with serial port to USB-serial converter and then to laptop

find the COM port with this converter inside Device Manager and then set this up in the configuration Wideband section (see wideband section in software users manual)

As for the rest of the wiring see the LC-1 manual which has the details for hooking it up

Anders_r · Post by **Anders_r** » Mon Aug 10, 2009 10:26 pm

Matt wrote:connect 3.5mm connector with serial port to USB-serial converter and then to laptop

find the COM port with this converter inside Device Manager and then set this up in the configuration Wideband section (see wideband section in software users manual)

As for the rest of the wiring see the LC-1 manual which has the details for hooking it up

The 3,5mm cable u can buy yes?:) or this will be homemade?

I only need 1 cable where my paint is and then usb to laptop yes ?:)

Matt · Post by **Matt** » Tue Aug 11, 2009 9:53 am

your LC-1 should have come with 3.5mm-serial plug. mine did

if not contact innovate to find out why its missing

Anders_r · Post by **Anders_r** » Thu Aug 13, 2009 10:02 am

looks like i got problems with my installation (it was there when i bought the car)

let me give u a pic!
:

These 2 are behind my AF gauge. the "in" is probably from the sensor ? cuz when i unplug it the gauge dont dont show afr anymore.
and then the "out" when i tried to find that cable .. i found that that was the cable to the pc??? so when i changed those 2 places i got it working in nistune but it shows 16,7 in idle on nistune and 14,7 on my gauge. but then i switch them back and now my gauge shows

new pic: whats whis ;/

i think its 14,9 my but the "1" is gone ;( why

John · Post by **John** » Thu Aug 13, 2009 7:34 pm

If Nistune and the wideband display shows different values you most likely chosen the wrong Wideband lookup table in the Nistune configuration.

Your gauge then is either broken or the cable in the back is not thoroughly connected.

Regards

John

Anders_r · Post by **Anders_r** » Thu Aug 13, 2009 9:05 pm

John wrote:If Nistune and the wideband display shows different values you most likely chosen the wrong Wideband lookup table in the Nistune configuration.

Your gauge then is either broken or the cable in the back is not thoroughly connected.

Regards

John

how can i get broken just if i change the cables? :S
the nr "1" is working cuz when i get power of and on its works and when car starting only 4,9 :S

Anders_r · Post by **Anders_r** » Thu Aug 13, 2009 9:49 pm

about the nistune, the lookup table is set at "innovate

Anders_r · Post by **Anders_r** » Thu Aug 13, 2009 11:00 pm

got it working now

John · Post by **John** » Fri Aug 14, 2009 1:26 am

Anders_r wrote:got it working now

What was the problem?

Anders_r · Post by **Anders_r** » Fri Aug 14, 2009 1:46 am

I really dont know

i just mixed some cables and sone violence

and now working good

zmyzgo · Post by **zmyzgo** » Sun Jan 31, 2010 12:26 pm

Hope this comes through:
http://www.innovatemotorsports.com/vide ... ntent.html

getting ready to do my permenat hook-up.....

Nistune Forums

how to connect LC1 to nistune?

how to connect LC1 to nistune?

LC-1 vid