NEO Tuning notes (Applies to R34/Stagea)

If it isnt a problem or a suggestion it probably goes here.

Moderator: Matt

Post Reply
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

NEO Tuning notes (Applies to R34/Stagea)

Post by Matt »

I've been going through the ECU code on these vehicles for the last few months. Not finished yet but some notes so far uploaded tonight

http://nistune.com/docs/Nistune%20NEO%2 ... Tuning.pdf

Covers what I have worked out so far about the boost sensor input, VE maps and TCS/ABS operation
Ben C
 

Posts: 13
Joined: Sat Mar 23, 2013 9:09 pm
Location: Adelaide

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Ben C »

Thanks Matt.

Typo on resolution 2 heading, should be disconnect MAP sensor.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Matt »

More important updates have been made to this document. The boost sensor must be connected for cases when TPS voltage drops (particularly on boost) and the TP is corrected to the current boost level. If the boost sensor is disconnected, TP will drop to a value of 132

This may affect load accessing of fuel and timing maps whilst on boost, and affect both fuel and timing. Several cases of intermittent TP drops to 132 or near have also been seen

If you are seeing over 18psi of boost, then increase maximum boost sensor voltage to 5100mv to avoid the check engine light
Peace
 

Posts: 60
Joined: Tue Sep 15, 2009 8:03 pm
Contact:

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Peace »

HI
Can anyone give some advice
I've got ENR34 ECU, we changed injectors to R35 GTR nad with boost sensor connected we get very bad reaction on accelerator pedal, Mixture goes super lean and then return to reach and then to normal, so the reaction on accelerator in very poor. If i touch pedal very very gently it causes car even to stall.

I made all recomended setting to boost sensor values so it not cause any limitations:
Boost sensor limit counter to 255
load limit max counter to 255
Boost sensor min voltage to 0
Boost sensor max voltage to 5100
But anyway i get this happen and if i disconnect boost sensor it goes normal again and reaction on gas very good.
IS tha mean i need to change injectors through K-const not Total Injector Multiplier?
An example log file is attached
Attachments
Nistune_2019-03-19_1205_24.csv
(9.56 KiB) Downloaded 161 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Matt »

Replied via email the correct boost sensor location. For anyone else, the boost sensor must be correctly plumbed pre-throttle body otherwise it will cause delay on acceleration

See pic from R34 service manual
Attachments
r34_boost_hose.png
(278.8 KiB) Downloaded 3290 times
STATUS
 

Posts: 119
Joined: Thu Jun 12, 2008 10:30 pm
Location: Melbourne
Contact:

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by STATUS »

Matt wrote: Thu Mar 21, 2019 10:23 pm Replied via email the correct boost sensor location. For anyone else, the boost sensor must be correctly plumbed pre-throttle body otherwise it will cause delay on acceleration

See pic from R34 service manual
If not fitted the boost sensor limit counters need adjusting to stop the hesitation.
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Matt »

Good to know. I had hesitation with R34 and boost sensor disconnected ... but thought I had modified the counters from 10 to 255
Dan_J
 

Posts: 20
Joined: Thu Feb 05, 2015 2:22 pm

Re: NEO Tuning notes (Applies to R34/Stagea)

Post by Dan_J »

hey matt,

trying not to clutter this thread, could i grab some help on this issue?
link below
https://forum.nistune.com/viewtopic.php?f=11&t=3742

thanks
Post Reply