B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Discussions concerning the M7790 cpu

Moderator: Matt

Post Reply
UNISA JECS
 

Posts: 367
Joined: Wed Jun 04, 2008 3:48 am
Location: USA Socal

B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by UNISA JECS »

Hey Matt I have a flex fuel board and I don't see any real documentation to help me install it any further then power and ground, can you help by telling me which wire go where, thanks

Charlie

P.S. I also need a feature pack for this ECU I don't see one available if you can make one for me that'll be great
Attachments
IMG_7326.JPG
FLEX FUEL BOARD
(2.53 MiB) Downloaded 2230 times
IMG_7324.JPG
94Y00 ECU
(2.57 MiB) Downloaded 2230 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by Matt »

B13 SR20DE 94Y00 does not have flex fuel (or feature pack support)

Our official list is here:
viewtopic.php?f=12&t=2874

B13 SR20DE does have documentation (for earlier models - as listed) which involves power and GND. The 5V power line goes off the regulator similar to S13 SR20DET ECU

The input line I am not sure about, since we don't have support for that hardware. It is one of the two green lines going to the potentiometer

Anyway... the reason why no FP support for this ECU is that it is not a common model ECU (earlier are more common so supported) and also this particular version is 64KB and uses a different address file and coding.

I have had a look at it but was unable to locate specific routines to patch in the Total injection multiplier and flex fuel code portions. This is similar for the later P10 SR20DE model ECU with 64KB code

I can give it another look when I have free time, but if you are wanting to get it working, perhaps source an earlier ECU which is in the support list and install into that one?
UNISA JECS
 

Posts: 367
Joined: Wed Jun 04, 2008 3:48 am
Location: USA Socal

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by UNISA JECS »

Ok Matt I got another ECU 23710-67Y00

I think I may have a caught a typo here

http://nistune.com/docs/Nistune%20Featu ... nstall.pdf

It says:
B13 SR20DE / S13 SR20DE / P10 SR20DE / S13 KA24DE
Remove resistor R226 (component marked 112)

But component R226 is not marked 112 BUT component R225 is marked 112 can you please advice which is it that is suppost to be removed R226 or R225.

Thank you
Attachments
IMG_7430.jpg
Just a picture of my 67Y00 take note of R225 vs R226 and the 112 designation on R225
(746.11 KiB) Downloaded 2185 times
nistuneflexfuel.JPG
I believe a typo is here
(157.2 KiB) Downloaded 2185 times
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by Matt »

I've updated the document. A better explanation is needed

The resistor number varies between hardware (R225/R226) but it is definitely the component with '112' written on it which needs removal (as this is a pullup/down resistor)

The second pictured ECU is B13 74Y00 which is same as you have so remove R225 on this one
UNISA JECS
 

Posts: 367
Joined: Wed Jun 04, 2008 3:48 am
Location: USA Socal

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by UNISA JECS »

Ok Matt here I am again the previous 67Y00 ECU ended up being a bad ECU had a blown out trace that i caught later on, so got a new ECU.


This ones a B13 SENTRA SE-R 64Y01 ECU and I have a question on the FLEX FUEL "OP" wire and the VR229 (Potentiometer) I had a look at the KA24DE ECU and it looks vary similar as this B13 ECU but can you tell me where I would solder the "OP" FLEX FUEL board wire to? Thank you and over look the picture below and tell me if it looks good to you, thanks

Image

Not sure if this is even relevant but I took a picture anyways cause I dont want to remove the wrong resistor especially cause one of them is so small I cant even read the text with my current magnifier lol and I noticed that the middle soldered pin under the actual potentiomeer location trace run through R226 and R225 well seems to terminate at R225 actually

Image
Image

This is from Nistune Feature Hardware Install PDF for the S13 KA24DE ECU not sure what is meant by lower ground wire then again mines a B13 SR20DE ECU and its 3 pots but only 2 green wires soldered on and ran over to VR229 in the middle of the ECU board)

Image

and this is the B13 SR20DE 64Y01 potentiometer
Image
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by Matt »

I've now added B13 SR20DE to the same page as S13 KA24DE in the hardware document

I've got a 67Y10 ECU here which is identical hardware to yours so have double checked all this. It is the same potentiometer wire (near R405) as the S13 KA24DE

Also the resistor must be the 112 marked resistor (1.1Kohm) which is a pullup from the potentiometer to 5V. Removing this allows the voltage to be pulled down with less resistance.

More important with the Zeitronix ECA-2 which has a weaker output than the Nistune board and cannot fight the pullup as well
UNISA JECS
 

Posts: 367
Joined: Wed Jun 04, 2008 3:48 am
Location: USA Socal

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by UNISA JECS »

Image
Matt
Site Admin
 

Posts: 8961
Joined: Sun Jan 29, 2006 1:45 am
Location: Adelaide, Australia
Contact:

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by Matt »

Looks good. Assume all working?
UNISA JECS
 

Posts: 367
Joined: Wed Jun 04, 2008 3:48 am
Location: USA Socal

Re: B13 SR20DE 94Y00 FLEX FUEL BOARD INSTALL

Post by UNISA JECS »

Matt wrote:Looks good. Assume all working?
Thanks Matt, im not able to test it yet cause I don't have a B13, I was just putting this together for a friend out of state, but I may actually be the one ending up testing and tuning it at a later date, and i'll will report back.
Post Reply