Got a new MTX-L power up at the desk top before installing, and first time to link to nistune,
did twice free air calibration, but the AFR reading in nistune is different from the gauge,
does the lookup table need to be manually adjust ?
Search found 256 matches
- Sun Jun 29, 2014 6:58 am
- Forum: Innovate
- Topic: MTX-L AFR reading in nistune different from the gauge ?
- Replies: 3
- Views: 6163
- Sat Jun 28, 2014 7:32 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
When first install 1.2.7 from 1.2.6, got the warning message boxes, but able to open nistune, just all pull down menu show "undef", Then, uninstall and reinstall 1.2.7, But 1.2.7 cannot be open. Uninstall 1.2.7 and remove HKEY_CURRENT_USER\Software\Nistune Developments\ and reinstall 1.2.7...
- Sat Jun 28, 2014 6:24 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
Could it be the problem ?
- Sat Jun 28, 2014 6:16 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
Got this after uninstall and reinstall , first show "Translate file cannot be open,
Menus and message box will not display correctly", and then this ....
Can't open nistune anymore !
Menus and message box will not display correctly", and then this ....
Can't open nistune anymore !
- Sat Jun 28, 2014 6:04 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
The crash screen is capture right after select the translation_english_ansi.ini
- Fri Jun 27, 2014 5:42 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
Trying to setup the translation and selected "translation_english_ansi.ini" and got this.
- Fri Jun 27, 2014 5:31 am
- Forum: Software Bugs
- Topic: Translation error 1.2.7
- Replies: 22
- Views: 8489
Re: Nistune Formal Release 1.0
Hi Matt,
What does it mean ?
What does it mean ?
- Tue Jun 24, 2014 5:50 am
- Forum: General Nistune Discussion
- Topic: Nistune Formal Release 1.2.21 [update]
- Replies: 88
- Views: 270138
Re: Nistune Formal Release 1.0
Should it be Version 1.2.6 ?
- Thu Jun 12, 2014 3:36 pm
- Forum: General Nistune Discussion
- Topic: Nistune Formal Release 1.2.21 [update]
- Replies: 88
- Views: 270138
Re: Nistune Formal Release 1.0
I think it should fix any problems associated with moving K too much and affecting tables depending on it such as this. I have not looked closely at closed loop on my S14 since putting the change in but will check it out Just load the address file inside the feature pack v1 floder ? Does the board ...
- Thu Jun 12, 2014 3:41 am
- Forum: General Nistune Discussion
- Topic: Nistune Formal Release 1.2.21 [update]
- Replies: 88
- Views: 270138
Re: Nistune Formal Release 1.0
In this PDF page 15, should it be RB26 ?Matt wrote:Documentation completed:
http://www.nistune.com/docs/Nistune_Feature_Pack_V1.pdf
- Tue Jun 10, 2014 3:28 pm
- Forum: General Nistune Discussion
- Topic: Nistune Formal Release 1.2.21 [update]
- Replies: 88
- Views: 270138
Re: Nistune Formal Release 1.0
Will the Total Injection Multiplier fix the S14 SR20 refuse to go to open loop at low rev high load (ie : O2 flage switched off but still not following AF target on the map) ?
- Sat Jun 07, 2014 7:40 pm
- Forum: AEM
- Topic: How to link AEM wideband failsafe gauge into nistune ?
- Replies: 1
- Views: 3592
How to link AEM wideband failsafe gauge into nistune ?
I have the AEM wideband failsafe gauge P/N 30-4900 connected via USB on my notwbook, the AEM software can correctly conneected, but in nistune software, there is "AEM Uego AFR gauge" for selection, but after selected AEM, there is no PORT can select, and the AEM AFR cannot be import into n...
- Wed May 21, 2014 6:42 am
- Forum: General Nistune Discussion
- Topic: How to convert wideband 0-5V analog signal to 0-1V ?
- Replies: 2
- Views: 2393
Re: How to convert wideband 0-5V analog signal to 0-1V ?
Hi Ringo, Thanks for your reply, I already have Zeitronix Zt-2, but I like the function of AEM wideband failsafe kit, but it does not have 0-1v narrowband simulation output, so trying to ask for help. After reading AEM instruction, found that it's analog output cannot be program to 0-1v, so I gave u...
- Wed Apr 30, 2014 2:54 am
- Forum: Type 1
- Topic: Ca18det + Holset Hx35 + E85 tune
- Replies: 29
- Views: 13232
Re: Ca18det + Holset Hx35 + E85 tune
It might be boost leak
- Sun Apr 20, 2014 6:32 pm
- Forum: General Nistune Discussion
- Topic: How to convert wideband 0-5V analog signal to 0-1V ?
- Replies: 2
- Views: 2393
How to convert wideband 0-5V analog signal to 0-1V ?
As title, for replacing narrow band signal, if the wideband does not have 0-1V analog output.