Nistune Forums

check this topic: http://forum.nistune.com/viewtopic.php?f=12&t=1279&hilit=Dlp+logging non-working link EGT)) I found another amplifier. http://www.ebay.com/itm/Temperature-Signal-Converter-Input-K-type-Thermocouple-Output-Voltage/331393972432?_trksid=p2045573.c100033.m2042&_trkparms=ai...

how to write egt log?
thermocouple type K has a range of 0-54 millivolt = 0-1370 degrees Celsius.
If you connect directly DLP \ BP?
or without the signal amplifier will not work? wrong

http://temperatures.ru/pdf/Type%28K%29.pdf

table may dwell duty cycle is in degrees of crankshaft rotation as Apexi PFC ? http://drag2ter.com/blog/wp-content/uploads/2011/05/rb26dwell.png http://drag2ter.com/blog/wp-content/uploads/2011/05/time.png http://drag2ter.com/blog/wp-content/uploads/2011/05/diff_time_same_angle.png http://drag2ter.c...

knock sensor connected to the DLP logger. through the zener diode 5 Volt. To protect the input logger.
lightly tapping the knock sensor, records the signal. on the oscilloscope is very short signal 50-200 micro seconds. about.

Idling I increased the card RPM/dwell and it improved a little work.
at high load that does not work! all also lost spark.
Code 21 is lit why? this may be the reason?

These are now using firmware.
HCR32_FOR_RB25_11U0F_MT_TPS_VCT_LEDOUT_v5_FP.ent
HCR32_FOR_RB25_11U0F_MT_TPS_VCT_FP_maps.bin
will wait for a new update!
a lot of posts on the topic counter knock some write that works well, others write that does not work well.

perform poorly coil LS2. those as in the middle http://www.bgsoflex.com/lscoil/ls2coiltest10.jpg ECU set r32 installed the latest ENT (HCR32_FOR_RB25_11U0F_MT_TPS_VCT_LEDOUT_v5_FP.ent) 1)increased dwell time as in the picture above. http://forum.nistune.com/download/file.php?id=2367 it gave me a sta...

Hi Matt. Install the latest ENT Fail to R32 ECU. not working knock warning panel. panel detonation is not active! what's the problem?

the problem was the knock sensor, removed the knock sensor! soldered 470Kom! ignition time beginning to keep as recorded in the map. before ignition time was -2 to 5. stock knock sensor is very sensitive, switched to the map detonation. prescribed MAF ER34. become better, but sometimes does not matc...

we will try out your recommendations! and upload the log.
We have tried to put the maf z32. doing Operations> Resize maf z32. load calculates incorrect
we did not remove the stock knock sensor 1 and 2, it can be the cause?

in idle, rich. 12: 1 at medium load approximately correct. levels boost, very lean 13-13.5 AFR at the time as soon as the boost 0.1-0.2, TP runs on the values ​​of 80 wherein the mixture on the map 11, in fact 13-14. load MAF does not match the load of TP 1) try to change the constant "K",...

use 32 ECU mec-r117. what version corrected code, dwell time at high speeds rev. will work on the EEPROM.

set 2 Maf ECR33. with "Y" pipes, signals Maf enter the Safc neo. signals are added for neo Safka (folded) and come into the ECU32. how to register 2 Maf?

My Type6 boards do exactly that, but allow realtime tuning using Nistune's awesome front end. As a matter of fact, my type6's started out life as a rom board. I considered seling a rom board, but you need emulators, cabling and the knowledge to tune them correctly. By using Nistune, the job is fast...

Now for the Stagea owner and any 80 pin H8 processor family - Here's a 3D render of the QFP to PLCC adapter to allow use of the new Type6 board. This adapter will allow you to simply plug in the Type 6 after fitting this masterpiece.. This PCB was not an easy task considering the small sizes involv...