Nistune Forums

Car Is done i drive today for the same tune and its ok:)) working perfect and idling also, BTW idling is much better with inserted MAF in pipe
thanks guys for helping
Did't tick TP load i just halve the values Constance is set at 153 and AFR is much better then with Z32

My fault I thought u had a RB20/25 :( sorry thought I was helping. Thanks mate for your helping!!!, I got Close, Constant value from 85 till 95 is close to good idling, I couldn't imagine that value could be so low so i didnot go low then 200 before, constant at 90 is close to 14.7 afr its jumping ...

remember you only halve the values on the R32 GTR ECU... because it has two MAF sensors and adds them together Matt i though that BlueRB240 swap RB26 also, sorry for my mistake:) Matt what i have realized also car was also idling normal at 200K value before water get to 70 and i test acceleration, ...

My maf is in a 2.75" pipe set up to blow through. http://i137.photobucket.com/albums/q211/Bluerb240/240%20stuff/P1010630.jpg My Kvalue is at 93. I'm running SARD 800cc low impedance injectors along with the lightning maf. will try tomorrow :) so you only change Maf from standard to ford lighti...

guricha I had the a problem with my Lightning maf setup. When I tried to start the car it wouldn't start and just run pig rich fouling up the plugs. I double check the injector latency and that was right. I then started to play with the K value and got it going. I didn't half the values on mine or ...

Matt, did the modified bin i sent through get your R31 running? No I couldnt get it working with that one (still required modification) and havent had a free block of time during the day (geez my car is loud) to get it all readjusted and it works to rich, what else i need to do ? adjusting injector...

Sounds like it. If its runs better with the default map with your resized cobra, might be a better starting point. I'm in the middle of trying to calibrate my HPX and that is nowhere near the spreadsheet values resized for Nissan 64 point :? Matt, yesterday i try it with original pipe, put it back ...

got today ford lighting AFM, its just huge !! dont know where to put idea is the next to remove sensor from pipe and put it in GTR cooler pipe, but what to do with size? If you change the pipe size the entire VQ map will need to be recalibrated and also injection multiplier i have 3 inch piping in ...

ticking TP load and halve values Dont tick the TP load for now... is this on a BNR32 ECU (R32 GTR)? This is the only ECU you use halve values on Have you got both AFM inputs connected together into the Cobra MAF? Yes Matt connection is ok both of AFM in nistune is getting signal and there is no err...

try to connect today ford lighting maf, but as soonest i try to re size maf in nistune to ford lighting and after ticking TP load and halve values car is starting like without maf, if i just load standard map without changing mafs engine is running ok, what can be reason ? i have installed maf befor...

try to connect today ford lighting maf, but as soonest i try to re size maf in nistune to ford lighting and after ticking TP load and halve values car is starting like without maf, if i just load standard map without changing mafs engine is running ok, what can be reason ? i have installed maf befor...

Dear Matt, i know you are busy all the time improve Nistune and our cars life also and just wander is there any plan to make separately software to have digital dash in car? i mean something like that? http://home.exetel.com.au/nds/NDSIdash/pictures/screenE.jpg for my option i will be glad to pay so...

Have option to buy Bosch 1600cc injectors and can Nistune allow me tune them ?

for E85 the Bosch EV14's are very good http://www.bosch-motorsport.de/en-US/literature/en-US/InjectionValveE_DataSheet_enUS_T6748843403.pdf you'll need a custom fuelrail though (for the 300ZX it'll need to be similar to this: http://www.drivenauthority.com/shop/WF_Z32fuelrail.html) Hi mate, Which o...

What model toughbooks are you guys running? The common ones seem to be the 18 and 29. 18 is the lesser machine but much lighter than the hefty 29 at 3.6kg. Is the touchscreen useable with NIStune? PL PL i have CF48 its really heavy :) but has really strong monitor stands, good for especially road t...