Search found 108 matches
- Thu Aug 23, 2012 7:21 pm
- Forum: General Nistune Discussion
- Topic: Brad Barnhills Virtual Dyno
- Replies: 33
- Views: 14929
Re: Brad Barnhills Virtual Dyno
Nice teamwork guys
- Sun Aug 12, 2012 2:43 pm
- Forum: Type 3/4/5
- Topic: Went blow through now idles lean
- Replies: 2
- Views: 1829
Re: Went blow through now idles lean
i changed back to draw through and the cars back to normal, blow through for the lose!
- Thu Aug 09, 2012 3:59 pm
- Forum: General Nistune Discussion
- Topic: Nistune 0.10.21 Release
- Replies: 52
- Views: 18062
Re: Nistune 0.10.21 Release
yea mines had some crash issues, i let it send a log or whatever it does.
- Wed Aug 08, 2012 2:26 am
- Forum: General Nistune Discussion
- Topic: Nistune 0.10.21 Release
- Replies: 52
- Views: 18062
Re: Nistune 0.10.21 Release
lmao!!
as long as the afr bein displayed is correct im fine with it showing 19.6.
as long as the afr bein displayed is correct im fine with it showing 19.6.
- Tue Aug 07, 2012 5:21 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
actually, i found that the ECR33 RB25DET was the correct vq map to use, but yes the maxima is where i got the maf from, not sure if the vq map has changed for the maxima in nistune recently but in the past i found it wasn't right. the only thing that changed when going blow through initially was maf...
- Tue Aug 07, 2012 2:38 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
just went for a test drive with the new bin, cold idle is fine, warm idle is lean for a few seconds then settles right on 14.7, a quick blip of the throttle shows 13 afr's then as the rpms settle it goes 11,12,13,14.7. cruise afrs are high 15's to mid 16's above 3000 rpm, 2500-3000 is 14.7-15.0. zer...
- Tue Aug 07, 2012 11:41 am
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
Here's a little background on what I've done. When I switched from the stock maf to the n60 I just put the wires from the n60 pigtail into the stock plug then taped it up with electrical tape, this was meant to be temporary but its worked without any noticeable problems, until now possibly. I've nev...
- Mon Aug 06, 2012 6:08 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
thank you sir.
- Mon Aug 06, 2012 4:44 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
Ok so I just loaded a stock de bin an changed it to 520 injectors and z32 maf, then copyed the s13 fuel maps and load scales and my timing map from the last bin, fired her up an she was mega lean, adjusted the injector latency from 600 to 820 was still stupid lean, then adjusted it to 900 an the afr...
- Mon Aug 06, 2012 1:30 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
gotcha, will give it a shot, thanks again!
- Mon Aug 06, 2012 12:09 pm
- Forum: General Nistune Discussion
- Topic: Nistune 0.10.21 Release
- Replies: 52
- Views: 18062
Re: Nistune 0.10.21 Release
It would be awesome if you can test the decel afr's for us man, when I first saw that I thought something was wrong with my tune until I switched to the tweaker gauge
- Mon Aug 06, 2012 8:59 am
- Forum: General Nistune Discussion
- Topic: Nistune 0.10.21 Release
- Replies: 52
- Views: 18062
Re: Nistune 0.10.21 Release
OK I did as you asked, the AFR tweaker gauge readings are identical to the ZDL program, and from what i can tell everything below 19.6 afr is the same in nistune as it is in the program, i checked at idle, and with my foot at 2000, 2500, 3000 rpm tryin to hold it as steady as i could while switchin ...
- Mon Aug 06, 2012 6:51 am
- Forum: General Nistune Discussion
- Topic: Brad Barnhills Virtual Dyno
- Replies: 33
- Views: 14929
Re: Brad Barnhills Virtual Dyno
First off, Big thanks for adding Nistune support, it saves me soo much time from having to convert logs from volts to % hehe. A quick question though, why did the graphs change so much? Yesterdays: http://i49.photobucket.com/albums/f285/lynch420/8-4-12b2b.jpg Todays: http://i49.photobucket.com/album...
- Sun Aug 05, 2012 10:38 pm
- Forum: General Nistune Discussion
- Topic: Nistune 0.10.21 Release
- Replies: 52
- Views: 18062
Re: Nistune 0.10.21 Release
ok, im going to be ordering a splitter aswell, so that should help sort the issue out since i'll be able to look at both at the same time heh.
- Sun Aug 05, 2012 10:36 pm
- Forum: Type 3/4/5
- Topic: high load high rpm WOT too rich
- Replies: 17
- Views: 6081
Re: high load high rpm WOT too rich
Cool, thanks again.