Search found 43 matches

by midian
Sun Feb 19, 2023 4:09 am
Forum: FAQs
Topic: IAT equipped MAF at Type1/2 boards (not equipped)
Replies: 2
Views: 2902

Re: IAT equipped MAF at Type1/2 boards (not equipped)

understood. thanks.
by midian
Mon Jan 30, 2023 7:49 pm
Forum: FAQs
Topic: IAT equipped MAF at Type1/2 boards (not equipped)
Replies: 2
Views: 2902

IAT equipped MAF at Type1/2 boards (not equipped)

I think this question was asked numerous times, but I searched many times here, or at other sourses and hadn't get an answer. Older MAFs (hot wire usually) had only one output - signal (they had temp sensor integrated, but there were no output). Some of descriptions shows it as "additional"...
by midian
Sat Dec 31, 2022 8:50 am
Forum: General Nistune Discussion
Topic: board operation and broken pin
Replies: 4
Views: 4872

Re: board operation and broken pin

e.g. should operate even with broken pin? anyway, flashed with coerrect image and soldered (just for testing - car starts - e.g. board working. soldering whole line will bi difficult anyway, so lpanned do same way - replace only pin/ as for source of pin from line - ordered same to TS-114-T-AA from ...
by midian
Wed Dec 28, 2022 3:48 am
Forum: General Nistune Discussion
Topic: board operation and broken pin
Replies: 4
Views: 4872

Re: board operation and broken pin

fixed as on attached photo.
been reprogrammed, tested, verified (e.g. operational?)
by midian
Tue Dec 27, 2022 7:16 am
Forum: General Nistune Discussion
Topic: board operation and broken pin
Replies: 4
Views: 4872

board operation and broken pin

Hi, Matt, got this board with ECU, but car wasn't starting, there were no connection to a laptop yet, after removed board and found broken pin(see attachments). after installation in my own board, Laptop tryed to connect, but messaged - "wrong MAF" etc, "reinstall board" or smth ...
by midian
Thu Jun 30, 2022 5:17 pm
Forum: General Nistune Discussion
Topic: Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421
Replies: 4
Views: 3017

Re: Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421

I think minimal coerrection to be done (see image)
Image
by midian
Fri Nov 26, 2021 12:00 am
Forum: General Nistune Discussion
Topic: Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421
Replies: 4
Views: 3017

Re: Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421

Understood.
Well,64 points.... Those points I have + ms Excel :p
by midian
Mon Nov 22, 2021 5:00 pm
Forum: General Nistune Discussion
Topic: Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421
Replies: 4
Views: 3017

Bosch maf HFM5 sensor 0 280 002 421, 0 281 002 421

Hi all, but generally Matt. there are bosch hot film sensors (same as gtr or z32 type), which capable to measure up to 1200m3/h. They re rare counterfate, and not so expensive as new oem z32. but the problem in correct voltage. If I don't mistaken, in early (0.9.xxx) revisions of ECU it was possible...
by midian
Mon Feb 17, 2020 9:17 pm
Forum: Type 1
Topic: new problem:o2 readings
Replies: 44
Views: 18202

Re: new problem:o2 readings

What is the part number on your ECU LID? Should look like: A18-xxxx xxx? understood,will do within week. Sorry I don't have any info on if the Z32 ECU has that circuitry. I can see there is a track to that pin (#17) on the ECU. Okay I've just hooked up an ECU since I got curious about this It appea...
by midian
Fri Feb 14, 2020 7:13 am
Forum: General Nistune Discussion
Topic: Type 1 board preprogrammed for type 2 ECU
Replies: 1
Views: 1101

Type 1 board preprogrammed for type 2 ECU

Hi all, I definitelly sure I'd read here (or at z31p forum - not sure exactly, pretty sure it was here) that it possible to use type 1 board in type 2 ECU. I also remember Matt confirmed this, but I can't find topic =( I have nistune base image programmer, so can DIY. So, I don't remember what shoul...
by midian
Thu Feb 13, 2020 8:36 am
Forum: Type 1
Topic: new problem:o2 readings
Replies: 44
Views: 18202

Re: new problem:o2 readings

Hi, Matt Sorry on delay. can you mention more correcly (a bit braking) what p/n s you need=) if I can check it w/out installing on a base image programmer. also, preparing to vg30de swap, want to ask one more question. I found at web (nistune.com also) that r33 and z32 ecus have almost same pinouts....
by midian
Fri May 31, 2019 6:21 am
Forum: Type 1
Topic: new problem:o2 readings
Replies: 44
Views: 18202

Re: new problem:o2 readings

it was 26p00,and was marked as 26p00. i'll check which one within a week (laptop broken down) I use now,but adr file for eudm is the only in rom/adr package,for 87. actually,newerthless it is 89 ecu, board type is similar to late eudm and 87 usdm,e.g. without soldering pins on board. actually,I thin...
by midian
Thu May 30, 2019 12:25 am
Forum: Type 1
Topic: new problem:o2 readings
Replies: 44
Views: 18202

Re: new problem:o2 readings

4 years passed, problem solved 1 month ago. Roman from Washington state, Z32 tuner, mentioned, that he met same situation, caused by improper base rom image writing. so... removed->jumper soldered->new base rom image (used 1987 EUDM, cause according to experience - closest to JDM VG) written->jumper...
by midian
Thu Jun 29, 2017 7:54 am
Forum: Software Bugs
Topic: installation of update issue
Replies: 2
Views: 2481

Re: installation of update issue

solved, occasionally - opened it via command line.
by midian
Thu Jun 29, 2017 7:50 am
Forum: Software Bugs
Topic: installation of update issue
Replies: 2
Views: 2481

installation of update issue

Used search - hadn't found an answer symptoms: downloaded 1.2.6 (76)- start-nothing. reboot at safe mode - start- diag box "can't start program" Own suggestions: system requirements changed (running 32 vista - yes still vista, cause anough for a laptop, which often get into garage). other ...