Search found 63 matches

by Bgtym
Tue Sep 29, 2020 1:45 am
Forum: Software Enhancements
Topic: crankshaft trigger vs cas
Replies: 5
Views: 3586

Re: crankshaft trigger vs cas

thanks for the complete answer Matt
one more question)
if you make a disc 180 marks on the crankshaft,
and transfer the 1 degree signal to the crankshaft?
can such a scheme be workable?

or leaving a signal of 120 degrees on the camshaft is all useless
by Bgtym
Wed Sep 23, 2020 4:18 pm
Forum: Software Enhancements
Topic: crankshaft trigger vs cas
Replies: 5
Views: 3586

crankshaft trigger vs cas

I have tunned many different control units. and I know the main Nissan synchronization problem The СAS has huge backlashes, and large backlashes from the timing belt. (I already created a thread on this forum) and in my hands was a converter kit from Ross performance. (synchronization from the crank...
by Bgtym
Thu Jan 24, 2019 4:33 am
Forum: Type 3/4/5
Topic: vh45de
Replies: 2
Views: 1583

vh45de

Hi Matt, which board is suitable for this ECU, there is no information in the manual
Image
Image
by Bgtym
Tue Sep 26, 2017 8:35 pm
Forum: Mechcnical and Running issues
Topic: backlash, camshaft position sensor. (CAS)
Replies: 3
Views: 4197

Re: backlash, camshaft position sensor. (CAS)

vq30det flywheel has labels 180
if install the disk on the crankshaft, a disk that has 180 holes (the crankshaft turns faster than the camshaft)
Install the optical sensor on the crankshaft, replace CAS signal "1" degree, signal "120" leave on standard CAS
you offer such an option?
by Bgtym
Wed Sep 20, 2017 9:24 pm
Forum: Mechcnical and Running issues
Topic: backlash, camshaft position sensor. (CAS)
Replies: 3
Views: 4197

backlash, camshaft position sensor. (CAS)

the drive problems of the camshaft position sensor do not allow the motor to be adjusted at high angles. 4 cases in my practice. detonation at high rpm, I seriously thought about when my friend installed the kit (ross performance converter box) after installing the kit ross performance converter box...
by Bgtym
Thu Jul 20, 2017 9:26 pm
Forum: Test Results
Topic: R35 GTR MAF, HPX MAF testing
Replies: 25
Views: 31867

Re: R35 GTR MAF, HPX MAF testing

Which turbine was used in this test?
by Bgtym
Wed Nov 30, 2016 4:28 pm
Forum: Mechcnical and Running issues
Topic: rb25det CAMSHAFT 272 duration
Replies: 1
Views: 5732

rb25det CAMSHAFT 272 duration

Hi guys I want to put on the the camshaft rb25det nonNEO, but don `t know how to choose the duration 265 or 272. if you set the duration 272 WTC need to be removed? and a maximum lift is possible be installed without rework? an example of what I found, the camshaft kelford 272 9.3. installed without...
by Bgtym
Tue Aug 23, 2016 3:15 am
Forum: General Nistune Discussion
Topic: Feature Pack updates + Information thread
Replies: 174
Views: 478035

Re: Feature Pack updates + Information thread

order to use the (Z32_FOR_RB25DET_41P03_MT_v4_FP_maps.bin) I have to write down the base image (Z32_VG30DETT_41P0F_MT_JDM_FP.ent)
by Bgtym
Mon Aug 22, 2016 4:49 am
Forum: General Nistune Discussion
Topic: Feature Pack updates + Information thread
Replies: 174
Views: 478035

Re: Feature Pack updates + Information thread

What ENT to use the new firmware? (Z32_FOR_RB25DET_41P03_MT_v4_FP_maps)

what is different (Z32_FOR_RB25DET_41P03_MT_v4_FP_maps.bin) and (Z32_FOR_RB25DET_41P03_MT_v3_FP_maps.bin)
by Bgtym
Fri Aug 05, 2016 6:32 pm
Forum: Type 2
Topic: rb25 with R32 ECU load going off the map
Replies: 18
Views: 6822

Re: rb25 with R32 ECU load going off the map

tuning the firmware with the "TIM" I understand)))
in my firmware is not Tim.
I have an old firmware Z32_FOR_RB25DET_41P03_MT_v3
the transition to MAF z32 I remove the check mark "half" and "GTR ECU"
by Bgtym
Thu Aug 04, 2016 5:07 am
Forum: Type 2
Topic: rb25 with R32 ECU load going off the map
Replies: 18
Views: 6822

Re: rb25 with R32 ECU load going off the map

adjust the "TIM" is very convenient! but the setting on the old "ENT" I now do not understand. (Z32_FOR_RB25DET_41P03_MT_v3) I changed the MAF on the z32, now it turns 80TP = 5 volts MAF? To use the the entire width of the fuel card I just need to turn down the TP? this figure bo...
by Bgtym
Mon Jul 25, 2016 4:24 am
Forum: Type 2
Topic: Z32 FPCM
Replies: 6
Views: 3578

Z32 FPCM

On the RB25 ECU / PIN 104 there's a control output for the Fuel-Pump to make the pump less noisy (maybe activated by TPS?) The Z32 ECU has exactly the same PIN/circuit (since my pump does not go into silent mode) Is there a flag for this I can monitor? and one more question Pin 6 and 19, fan control...
by Bgtym
Thu Jun 30, 2016 4:15 pm
Forum: Type 2
Topic: E85 maps Activation
Replies: 14
Views: 7035

Re: E85 maps Activation

we do not have Flex converter!
unless apply a voltage of 5 volts on slot vr272, it activates the E85 map ?
I want to fasten the pressure sensor (switch), which at the time of the methanol water will close the circuit and provide power to the JCU to activate E85 map
by Bgtym
Wed Jun 29, 2016 5:59 pm
Forum: Type 2
Topic: E85 maps Activation
Replies: 14
Views: 7035

E85 maps Activation

Hi Matt, new season, new ideas))
we use the z32 EKU and Feature Pack
also we use the water methanol injection
when applying methanol necessary to raise the ignition timing and adjust the AFR
is it possible to activate the map for E85 while submitting the water methanol
by Bgtym
Wed Oct 07, 2015 3:27 pm
Forum: Type 2
Topic: knocking on the boost, the angle of 8 degrees
Replies: 9
Views: 4468

Re: knocking on the boost, the angle of 8 degrees

Matt wrote:Did you uninstall before reinstall?

Please post a debug log here (or email to info AT nistune.com)

File > Configuration > Debug logging

I created a thread in another section.)) where I threw Debug logging
viewtopic.php?f=5&t=3224

You can delete this topic