Search found 73 matches

by brett_32i
Fri Mar 29, 2013 12:16 pm
Forum: Type 1
Topic: signals spiking - but not conected
Replies: 7
Views: 2288

Re: speed sensor spike - but not conected

and another one showing speed spike, rpm to 79000, and neutral switch on?
by brett_32i
Fri Mar 29, 2013 12:11 pm
Forum: Type 1
Topic: signals spiking - but not conected
Replies: 7
Views: 2288

Re: speed sensor spike - but not conected

ok, i took a snap shot of the log with the speed sensor spiking.
consult view shows the neutral switch flashing on at exactly the same time? (again, neither are connected, removed from loom)
by brett_32i
Fri Mar 29, 2013 12:08 pm
Forum: Type 1
Topic: signals spiking - but not conected
Replies: 7
Views: 2288

Re: speed sensor spike - but not conected

well i installed another loom to see if that would take care of some of these odd signals, but it didnt. the attached log is probably one of the best, it shows a few good pulls, and the odd signal issue. @ 1:30.4 the air con, nuetral, start, and tps indicators all flash on, but none are connected? t...
by brett_32i
Fri Mar 29, 2013 11:44 am
Forum: Type 1
Topic: MAF voltage in log playback issue
Replies: 16
Views: 5147

Re: MAF voltage in log playback issue

sorry to bring this up again, just had a chance to record a couple of runs.
now this one i saved as a "good run" and when i glanced at the boost gauge it was around 18psi.
i would have thought that the maf would have to be reading 7 volts, maxed out. it is just a vl maf in a 3" pipe.
by brett_32i
Tue Mar 19, 2013 10:49 am
Forum: Type 1
Topic: MAF voltage in log playback issue
Replies: 16
Views: 5147

Re: MAF voltage in log playback issue

ah thats good. checked the tick box option and offset is disabled, so yes, approaching 5volts under that load makes sense to me. thanks
by brett_32i
Tue Mar 19, 2013 9:23 am
Forum: Type 1
Topic: MAF voltage in log playback issue
Replies: 16
Views: 5147

Re: MAF voltage in log playback issue

so do my values look ok?
or should my value under that much load already be up over 5v (with offset)?
by brett_32i
Sat Mar 09, 2013 4:47 pm
Forum: Type 1
Topic: MAF voltage in log playback issue
Replies: 16
Views: 5147

Re: MAF voltage in log playback issue

so to make it go back to offsetting as required, i would just open up a base vl file, copy maf translation, then reopen my file and paste it in? it will then see a std vl translation and apply offset as necessary? at idle, maf(in nistune) is currently reading 2 volts is that where is should be for v...
by brett_32i
Sat Mar 09, 2013 4:31 pm
Forum: Type 1
Topic: Increased rev limit versus maps and scalers
Replies: 3
Views: 1946

Re: Increased rev limit versus maps and scalers

you could always set your scalers so you can adjust values to your new rev limit?
by brett_32i
Sat Mar 09, 2013 4:19 pm
Forum: Type 1
Topic: Knock count reading, but not connected
Replies: 7
Views: 2332

Re: Knock count reading, but not connected

ok, so although the ecu is reading something, nothing is actually being done with the input. ill just ignore it then.
by brett_32i
Wed Mar 06, 2013 9:10 pm
Forum: Type 1
Topic: Knock count reading, but not connected
Replies: 7
Views: 2332

Re: Knock count reading, but not connected

so i just ignore it?
or set the ecu to ignore it?
by brett_32i
Wed Mar 06, 2013 12:56 pm
Forum: Type 1
Topic: Knock count reading, but not connected
Replies: 7
Views: 2332

Knock count reading, but not connected

hi,
another ghost reading!

my ecu doesn't have a knock board as it isn't turbo (but it thinks it is)
i am getting erroneous readings for knock count.
can i disable it in nistune?
by brett_32i
Tue Mar 05, 2013 7:38 pm
Forum: Type 1
Topic: signals spiking - but not conected
Replies: 7
Views: 2288

Re: speed sensor spike - but not conected

thats exactly where it is terminated. about 10mm out of ecu with tape on it.
wondering if i should ground it?
by brett_32i
Sun Mar 03, 2013 12:50 pm
Forum: Type 1
Topic: wrong ecu selected?
Replies: 2
Views: 1437

wrong ecu selected?

does it matter what ecu nistune detects?
my ecu is a non turbo rb30, and i was using the cr31 adr.
when conencted, it said they didnt match and the actual ecu was vlt??
so i went with it and it works, but should i be worried and somehow override it?
by brett_32i
Sat Mar 02, 2013 6:54 pm
Forum: Type 1
Topic: signals spiking - but not conected
Replies: 7
Views: 2288

signals spiking - but not conected

attached shows the speed sensor spike to 400k's, and battery drop to 0. there is also another spot in log that you can see speed read 4 k's and a slight dip in battery.

Thing is, speed sensor is not connected. it is trimmed at plug with heat shrink around it.
should i ground it???
by brett_32i
Tue Jan 10, 2012 9:01 pm
Forum: Type 1
Topic: anyone got a tune VL turbo z32 airflow ,gtr inj will pay
Replies: 5
Views: 2433

Re: anyone got a tune VL turbo z32 airflow ,gtr inj will pay

Hey Matt

Did you get any further with this tune?

I now have a set of gtr injectors and was looking for a tune to reference.