Nistune Forums

I tried multiple versions of Nistune figuring that was the problem, but nope. Currently running the newest beta version. Everything is working fine including the consult dashboard (shows o2's, water temp, rpm, speed, codes, etc) but I cannot open the consult gauges. Clicking the button does nothing ...

Thanks for the quick reply Matt. I guess I never noticed the relay light up because I wasn't having fuel issues. I'll update versions as I am currently using 0.10.1 with a build date of May 24, so hopefully that will fix that issue. When you say to check the a/c solenoid function how do I go about t...

Hey, Just have a couple questions for my Z32. One thing I noticed the other day is in the consult vehicle display the fuel pump rly is highlighted red at all times. I swapped the relay and there was no change. I am wondering what this means because I am actually attempting to figure out why I am hav...

Pulled the wires through and made the solders nicer. It still didn't work even with perfect continuity so I took it to an electronics repair shop and was told the solders were fine and none of the tracks were damaged...I was hoping for damage. Here are some pictures of board/etc. I noticed the pins ...

I'll pull them in up to the plastic (hopefully get a better solder connection). I'll also remove the board, though I am pretty sure that isn't the issue since I have tried the original chip twice and it has been fine. If none of that gets it working I'll take it over to an electronics repair shop to...

Tested continuity.

With multimeter set to "20k" on the resistance setting checking from the solder point on the daughterboard to the solder point on the bottom of the ecuboard I would get a reading at .1 (or .01 cant remember) from all the wires.

Well I took pics and they do make my solder work look really nasty...Not very visible to the eye but it sure looks bad in pictures. I also learned I have very bad picture taking skills....not easy to get that board into focus. I'll check continuity after I post this. If you see any areas you can pin...

1 goes to D. (purple is D and black is A)

The daughterboard is labeled Z32 91P13 (might be 41P13 tough to tell).
ECU is labeled: 23710 41P14.

I'd check connectivity (have multimeter) but I'm not sure what I would be checking.

Reinstalled the old chip (left the wires I soldered there). Car was perfectly normal and I could connect via consult.

I'll wait for replies before I try anything else with the Nistune board.

Well redid the connections. Bolted the ecu all the way in to make sure it was grounded. Same issue as before. No connection to consult. My check engine light is on and every time I turn on the ignition the a/c fan turns on (never did that before installing nistune). As far as I can tell the ecu can ...

Well I got it to connect with the new cable. Downloaded my old tune. Then I installed the daughterboard...and now I cannot connect again with anything. The car will start and idle but will not give me any codes via the flashing led (or obviously consult). I assume this is limp mode and I installed s...

I bought a blazt usb consult cable that will arrive today. I know others who have used it with success. I figure the issue was my ebay consult cable..it was just strange it worked with other programs.

Im placing mine in the testpipe - a few inches after the end of the downpipe. It is fine to put the sensor in your downpipe if it is only for a first tune. Just make sure not to keep it there to long or you'll be buying a new sensor in no time. I was going to do that but I figured I might as well ge...

Ya I've decided this is purely a connectivity issue and I'm not sure what to do. When I attempt to connect by pressing the consult button it says "Nistune cannot find the correct USB drivers. Please reinstall USB drivers"

Hi, I have a chipped z32 ecu. I am wanting to download the chipped bin file so I can use that as a base map for when I install Nistune onto the board. It is not allowing me to connect to consult however. I can connect with my cable to blazt, ecutalk, etc. but not Nistune (or at least that is what it...