Search found 27 matches
- Wed Jan 01, 2020 8:18 pm
- Forum: Type 1
- Topic: AEM Smart Coil and tacho
- Replies: 5
- Views: 4069
Re: AEM Smart Coil and tacho
Yeah, that or its expecting a high voltage feedback from the coil discharging to run the tacho and tell the ECU the coil has fired. There is 2.2k resistor inline from the blue wire to the tacho so I think it'll be a high voltage signal. But this is the kicker. If I try run the coil without the blue ...
- Tue Dec 31, 2019 11:06 am
- Forum: Type 1
- Topic: AEM Smart Coil and tacho
- Replies: 5
- Views: 4069
Re: AEM Smart Coil and tacho
Hey Matt,
Your right, the tacho output for the ECU is from the CAS. The tacho output for the gauge cluster is a signal from the coil. I may need to get an adapter to make it work.
Thanks for your reply
Your right, the tacho output for the ECU is from the CAS. The tacho output for the gauge cluster is a signal from the coil. I may need to get an adapter to make it work.
Thanks for your reply
- Mon Dec 30, 2019 3:22 pm
- Forum: Type 1
- Topic: AEM Smart Coil and tacho
- Replies: 5
- Views: 4069
AEM Smart Coil and tacho
Hey all, Have wired in an AEM Smart Coil (IGN1A) and have the car running and driving well but tacho not working. https://drive.google.com/thumbnail?id=1yNF1nBG6uME-6G1JOxKIh2amixccE9QO https://drive.google.com/open?id=1yNF1nBG6uME-6G1JOxKIh2amixccE9QO Car is 1987 Z31 with corresponding ECU and a bu...
- Tue Jan 07, 2014 9:29 pm
- Forum: Type 2
- Topic: RB20DET TP spike
- Replies: 7
- Views: 3203
Re: RB20DET TP spike
Does it have vvt by chance?
- Tue Jan 07, 2014 9:12 pm
- Forum: Type 1
- Topic: Z31 cold start issues
- Replies: 2
- Views: 2432
Re: Z31 cold start issues
Ahh, I see. Ill make some changes and see how I go tomorrow morning. I managed to get it a little better by changing the latency of the injectors but its still a bit shit. Thanks Matt.
By the way, got that 32gtr ecu sorted too, working nicely now .
By the way, got that 32gtr ecu sorted too, working nicely now .
- Sat Jan 04, 2014 4:34 pm
- Forum: Type 1
- Topic: Z31 cold start issues
- Replies: 2
- Views: 2432
Z31 cold start issues
Howdy Having an issue lately with cold start. The car will start fine and then after a few seconds it leans right off until it dies. It will do this until it gets to about 40 degrees engine temp and then it runs better. The log shows that as the engine starts to lean off from 13afr, nothing changes ...
- Thu Oct 03, 2013 8:12 pm
- Forum: Type 1
- Topic: Can i use readings off nistune to diagnose my MAF?
- Replies: 4
- Views: 2661
Re: Can i use readings off nistune to diagnose my MAF?
For sure man! if there is any irregularities in the voltage while you are driving like voltage spikes or drops then you will be able to see it for sure. Even just have the laptop in the engine bay and monitor your readings while you fiddle with the maf.
- Fri Aug 30, 2013 9:01 pm
- Forum: Type 1
- Topic: Idle problem
- Replies: 23
- Views: 15449
Re: Idle problem
I have had this same problem for as long as I can remember on my 87 Z. I have learned to just deal with it because I've tried everything in Nistune and it just wont get any better. Although I have changed my dizzy assembly and it seems to be happier but that might just be in my head. Haven't had tim...
- Mon Aug 26, 2013 8:37 pm
- Forum: Type 2
- Topic: VG30DETT FuelPressure drop help!!!
- Replies: 2
- Views: 1962
Re: VG30DETT FuelPressure drop help!!!
Changed your filter recently?
- Wed Jun 01, 2011 6:59 pm
- Forum: Type 1
- Topic: Unknown ECU, Z31
- Replies: 5
- Views: 3900
Re: Unknown ECU, Z31
Ah, ok. Ive just seen it hit 8 volts at some stages, seems to be after i wash the car so water must be getting in there somewhere and making it play up..
All good, thanks for the help Matt.
All good, thanks for the help Matt.
- Sun May 29, 2011 10:28 pm
- Forum: Type 1
- Topic: Unknown ECU, Z31
- Replies: 5
- Views: 3900
Re: Unknown ECU, Z31
Where would the Zener diode go on this board? Yeah, i kinda buggered a few of the solder pads when i was putting the chip on :p..
- Sat May 28, 2011 9:23 pm
- Forum: Type 1
- Topic: Unknown ECU, Z31
- Replies: 5
- Views: 3900
Unknown ECU, Z31
Howdy Does anyone know what kind of ECU this is? Its supposed to be an Australian delivered manual 87 300ZX Turbo. While the outter case has the right numbers stamped onto it, inside its different and a google search doesnt come up with anything on the ECU number.. Reason Im asking is because I want...
- Fri Nov 05, 2010 9:17 pm
- Forum: B.S.
- Topic: Head Gasket CA18DET bullet proof
- Replies: 2
- Views: 4533
Re: Head Gasket CA18DET bullet proof
You might need to o-ring the block, thats a shit load of boost..
- Sun Oct 24, 2010 5:10 pm
- Forum: Software Bugs
- Topic: Nistune disappears
- Replies: 1
- Views: 1821
Nistune disappears
Howdy I've been having this problem for a while but just been working around it. Im running the software on a Toshiba Tecra A3X and for some reason, if i use the pad thing to move the mouse around and touch it to click on something, everything will disappear in the program. All thats left is an empt...
- Sat Apr 17, 2010 9:19 am
- Forum: B.S.
- Topic: Matts side projects
- Replies: 89
- Views: 333361
Re: Matts side projects
Love the car